Kohler Comand Pro CH1000 Скачать руководство пользователя страница 139

Страница: 139 / 142

10.29

Section 10

Reassembly

Figure 10-114. Connect Spark Plug Leads.

Prepare the Engine for Operation

The engine is now completely reassembled. Before
starting or operating the engine, be sure to do the
following.

1. Make sure all hardware is tightened securely.

2. Make sure the oil drain plugs, Oil Sentry™

pressure switch, and a new oil

lter are installed.

3. Fill the crankcase with the correct amount,

weight, and type of oil. Refer to oil
recommendations and procedures in Section 1

Safety and General Information

and in Section

Lubrication System

4. Adjust the carburetor, idle fuel needles, or idle

speed adjusting screw as necessary. Refer to
Section 5,

Fuel System and Governor

Testing the Engine

It is recommended that the engine be operated on a
test stand or bench prior to installation in the piece of
equipment.

1. Set the engine up on a test stand. Install an oil

pressure gauge. Start the engine and check to
be certain that oil pressure (20 psi or more) is
present. Run the engine at idle for 2-3 minutes,
then 5-6 minutes more between idle and
midrange. Adjust the carburetor mixture se

ings

as necessary (as available).

2. Adjust the governed idle and high speed (RPM)

to required se

ings. Make sure the maximum

engine speed does not exceed 3900 RPM (no
load).

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды