background image

10.7

Section 10

Reassembly

10

Oil Seal

3.0 mm 
(0.118 in.)

Figure 10-26. Oil Seal Depth in Closure Plate.

 

4.  Apply a light coat of clean engine oil to the inner 

surface of the main bearing.

Oil Pump Assembly

The oil pump is mounted inside the closure plate. If 
service was required and the oil pump was removed, 
refer to the assembly procedures under Oil Pump 
Assembly in Section 9.

Install Closure Plate Assembly

 

1.  Make sure the sealing surfaces of the closure 

plate and crankcase are clean, dry, and free of any 
nicks or burrs. Install a new O-ring in the closure 
plate. See Figure 10-27.

O-ring

Figure 10-27. O-ring Installed.

  2.  Install a new closure plate gasket onto the 

crankcase.

  3.  Make sure the oil pump is installed and the oil 

pickup tube faces outward at lower end.

Notch

Main 
Bearing

Figure 10-24. Installed Main Bearing In Closure 
Plate.

Oil Seal

  1.  Check to make sure there are no nicks or burrs in 

the cranksha

ft

  seal bore of the closure plate.

  2.  Lightly oil the outside diameter of the oil seal.

  3.  Install the oil seal into the closure plate using a 

seal driver. See Figure 10-25. Make sure the oil 
seal is installed straight and true in the bore to 
the depth shown in Figure 10-26.

Oil Seal

Oil Seal

Figure 10-25. Installed Oil Seal in Closure Plate.

Содержание Comand Pro CH1000















































































































































Отзывы: