Kohler Comand Pro CH1000 Скачать руководство пользователя страница 134

Страница: 134 / 142

10.24

Section 10
Reassembly

Install Control Bracket and Air Cleaner
Assembly

1. Position the control bracket assembly onto

the two intake manifold bosses. Align the rear
supports with the top valley ba

ﬄ

e/cylinder head

mounting screw locations and install the two
screws, but do not fully tighten. See Figure 10-94.

Rear Mounting
Locations

Control Bracket

Figure 10-94. Installing Control Bracket.

2. Connect the choke link to the control pivot pin.

Reinstall the washer and secure with a

new

push-

on pal nut. See Figure 10-95.

Push-On Nut

Choke Link

Washer

Figure 10-95. Installing Choke Link and Push-On
Nut.

3. Install a new air cleaner elbow gasket onto the

carburetor mounting studs.

4. Slide the air cleaner assembly onto the four

carburetor mounting studs. Align the two
forward mounting holes in the base with the
mounting holes/bosses of the intake manifold
and control bracket. A

ach the ground lead

under the hex nut as originally installed. Install
the remaining three hex nuts and start the two
hex

ange screws. Install the rear mounting

screws into the valley ba

ﬄ

e/cylinder head. Check

the positions of all parts then torque the four hex

ange nuts to

7.9 N·m (70 in. lb.)

in the sequence

shown (Figure 10-98), and the four hex

ange

screws to

9.9 N·m (88 in. lb.)

. See Figures 10-96,

10-97, and 10-98.

NOTE: The

low-pro

le air cleaner is installed the

same way as the heavy-duty air cleaner.

Mounting Nuts

Breather Hose

Vent Hose

Ground Lead

Figure 10-96. Mounting Air Cleaner and Hoses.

Mounting Screws

Figure 10-97. Installing Air Cleaner and Control
Bracket Screws.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Kohler Comand Pro CH1000, Руководство по обслуживанию, Страница: 134 / 142

Результаты поиска

Содержание Comand Pro CH1000

Отзывы: