Kohler Comand Pro CH1000 Скачать руководство пользователя страница 113

Страница: 113 / 142

10.3

Section 10

Reassembly

2. If the governor gear sha

was removed, press or

lightly tap the replacement sha

into the closure

plate to depth shown in Figure 10-10.

Governor
Gear Shaft

Figure 10-9. Installed Governor Gear Shaft.

Governor
Gear Shaft

12.66 mm
(0.498 in.)

Crankcase
Surface

Figure 10-10. Governor Gear Shaft Press Depth.

3. Lubricate the governor cross sha

bearing

surfaces in the crankcase with engine oil. Insert
the end with the

at for the governor gear yoke

into the crankcase

rst and position so the

at is

. See Figure 10-11.

Governor

Governor
Cross Shaft

Cross Shaft

Figure 10-11. Installing Governor Cross Shaft.

Notch

Main
Bearing

Figure 10-6. Installed Main Bearing.

Install Governor Shafts, Seal, and
Governor Gear

If the governor sha

s, seal, and/or governor gear were

removed, reassemble as follows.

1. Lightly oil the lip and outside diameter of the

new governor cross sha

seal. Install the seal into

the crankcase to the depth shown in Figure 10-8.

Seal

Figure 10-7. Installing Governor Cross Shaft Seal.

Oil Seal

Seal depth

1.5-2.0 mm (0.059-0.078 in.)

Crankcase
Surface

Figure 10-8. Governor Shaft Seal Depth.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды