Kohler Comand Pro CH1000 Скачать руководство пользователя страница 75

Страница: 75 / 142

7.23

Section 7

Electrical System and Components

Brush Replacement

The brushes and springs are serviced as a set (4). Use
a new Kohler Brush and Spring Kit, if replacement is
necessary.

1. Perform Steps 1-5 in Starter Disassembly.

2. Remove the two screws securing the brush

holder assembly to the end cap (plate). Note the
orientation for reassembly later. See Figure 7-38.
Discard the old brush holder assembly.

Figure 7-38. Removing Brush Holder.

3. Clean the component parts as required.

4. The new brushes and springs come preassembled

in a brush holder with a protective sleeve that
will also serve as an installation tool. See Figure
7-39.

Figure 7-39. Service Brush Kit.

5. Perform Steps 10-13 in the Starter Reassembly

sequence. Installation must be done a

er the

armature, drive lever, and frame are installed, if
the starter has been disassembled.

Starter Service

Clean the drive lever and armature sha

. Apply

Kohler electric starter drive lubricant (see Section 2)
(Versilube G322L or Mobil Temp SHC 32) to the lever
and sha

. Clean and check the other starter parts for

wear or damage as required.

Starter Reassembly

1. Apply drive lubricant (see Section 2) to the

armature sha

splines. Install the drive pinion

onto the armature sha

2. Install and assemble the stop collar/retainer

assembly. See Figure 7-40.

a. Install the stop collar down onto the

armature sha

with the counter bore (recess)

up.

b. Install a new retainer in the larger (rear)

groove of the armature sha

. Squeeze with a

pliers to compress it in the groove.

c. Slide the stop collar up and lock it into

place, so the recess surrounds the retainer
in the groove. If necessary, rotate the pinion
outward on the armature splines against the
retainer to help seat the collar around the
retainer.

Figure 7-40. Installing Stop Collar and Retainer.

NOTE: Always use a new retainer. Do not reuse old

retainers which have been removed.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды