Kohler Comand Pro CH1000 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 142

background image

1.1

Section 1

Safety and General Information

1

Section 1

Safety and General Information

Safety Precautions

To ensure safe operation please read the following statements and understand their meaning. Also
refer to your equipment manufacturer's manual for other important safety information. This manual
contains safety precautions which are explained below. Please read carefully.

WARNING

Warning is used to indicate the presence of a hazard that

can

cause

severe

personal injury, death, or

substantial property damage if the warning is ignored.

CAUTION

Caution is used to indicate the presence of a hazard that

will

or

can

cause

minor

personal injury or

property damage if the caution is ignored.

NOTE

Note is used to notify people of installation, operation, or maintenance information that is important
but not hazard-related.

For Your Safety!

These precautions should be followed at all times. Failure to follow these precautions could result in injury to
yourself and others.

Rotating Parts can cause severe
injury.

Stay away while engine is in
operation.

WARNING

Rotating Parts!

Keep hands, feet, hair, and clothing
away from all moving parts to prevent
injury. Never operate the engine with
covers, shrouds, or guards removed.

Hot Parts can cause severe burns.

Do not touch engine while operating
or just a

ft

er stopping.

WARNING

Hot Parts!

Engine components can get extremely
hot from operation. To prevent severe
burns, do not touch these areas while
the engine is running - or immediately
a

ft

er it is turned o

ﬀ

. Never operate

the engine with heat shields or guards
removed.

Accidental Starts can cause severe
injury or death.

Disconnect and ground spark plug
leads before servicing.

WARNING

Accidental Starts!

Disabling engine. Accidental
starting can cause severe injury or
death.

Before working on the engine

or equipment, disable the engine as
follows: 1) Disconnect the spark plug
lead(s). 2) Disconnect negative (-)
ba

tt

ery cable from ba

tt

ery.

«
...
3
4
5
6
7
...
»

Содержание Comand Pro CH1000















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Comand Pro CH1000

Бренд: Waldbeck Страницы: 72

Бренд: RCGF Страницы: 22

SEL Plus-RC Series

Бренд: Selve Страницы: 172

Бренд: Daedong Страницы: 51

MaxxForce DT 10

Бренд: Navistar Страницы: 109

Бренд: Daewoo Страницы: 199

Бренд: Man Страницы: 92

Бренд: Siemens Страницы: 4

SIMOTICS A-1FV5

Бренд: Siemens Страницы: 66

Бренд: Siemens Страницы: 56

SIMODRIVE POSMO A

Бренд: Siemens Страницы: 58

Бренд: Siemens Страницы: 100

Simotics HV C 1NA14544WA600AG0-Z

Бренд: Siemens Страницы: 112

SIMOTICS DP 1PC13

Бренд: Siemens Страницы: 100

SIMOTICS DP 1PC134

Бренд: Siemens Страницы: 120

SIMOTICS HT Series

Бренд: Siemens Страницы: 128

Бренд: Siemens Страницы: 136

SIMOTICS DC 1GH5

Бренд: Siemens Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды