Kohler Comand Pro CH1000 Скачать руководство пользователя страница 92

Страница: 92 / 142

8.12

Section 8
Disassembly

NOTE: These engines use valve stem seals on the

intake and exhaust valves. Use a new seal
whenever valves are removed, or if the seal is
deteriorated in any way. Never reuse an old
seal.

4. Repeat the above procedure for the other cylinder

head.

Do not

interchange parts from one cylinder

head to the other.

Remove Breather Assembly

1. Remove the four fasteners securing the breather

assembly, breather adapter (style based on spec),
and gaskets to the crankcase.

2. Carefully break the gasket seals and remove all

parts. Do not pry on the sealing surfaces as it
could cause damage resulting in leaks. Note the
assembly and orientation of parts. See Figures
8-48 and 8-49.

Breather

Breather
Adapter

Figure 8-48. Removing Breather Assembly.

Breather Adapter

Breather Adapter
(Certain Models)

(Certain Models)

Gasket

Figure 8-49. Removing Breather Adapter.

Remove Oil Reservoir and Pickup Screen

1. Remove the eight screws securing the oil

reservoir and gasket to engine.

Figure 8-50. Removing Oil Reservoir.

2. Remove the mounting screw and carefully work

the pickup screen o

ﬀ

the end of the pickup tube.

See Figure 8-51.

Mounting Screw

Pickup Screen

Pickup Tube

Figure 8-51. Removing Pickup Screen.

Remove Closure Plate Assembly

1. Remove the fourteen hex

ange screws securing

the closure plate to the crankcase. See Figure 8-52.

Figure 8-52. Removing Closure Plate Screws.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды