Kohler Comand Pro CH1000 Скачать руководство пользователя страница 89

Страница: 89 / 142

8.9

Section 8

Disassembly

Mounting
Screws

Molded Clips

Figure 8-33. Removing Stator.

4. Unhook the wiring harness from the molded

clips if it is being serviced separately. See Figure
8-34.

Molded
Clip

Wiring
Harness

Molded
Clip

Figure 8-34. Removing Wiring Harness.

Remove Backing Shroud Assembly

1. Remove the four mounting screws securing the

backing shroud assembly to the crankcase. See
Figure 8-35.

Backing
Shroud
Assembly

Screws

Figure 8-35. Removing Backing Shroud Mounting
Screws.

Remove Spark Plugs

1. Remove the spark plug from each cylinder head.

Figure 8-36. Removing Spark Plugs.

Remove Valve Covers and Fuel Pump

WARNING: Explosive Fuel!

Gasoline is extremely

ammable and its vapors can explode

if ignited. Store gasoline only in approved containers, in
well ventilated, unoccupied buildings, away from sparks or

ames. Do not

ll the fuel tank while the engine is hot or

running, since spilled fuel could ignite if it comes in contact
with hot parts or sparks from ignition. Do not start the
engine near spilled fuel. Never use gasoline as a cleaning
agent.

NOTE: Based on the style of fuel pump used refer to

the following when removing valve covers.

Mechanical Fuel Pump

1. The mechanical fuel pump is part of the valve

cover and not serviced separately. Remove with
the valve cover. Disconnect the fuel lines at the
fuel pump

ings. See Figure 8-37. Properly

contain any remaining fuel.

Figure 8-37. Disconnecting Fuel Lines.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды