Kohler Comand Pro CH1000 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 142

background image

5.10

Section 5
Fuel System and Governor

Disassembly/Overhaul

1. Clean the exterior surfaces of dirt or foreign

material before disassembling the carburetor.
Remove the four mounting screws and separate
the fuel bowl from the carburetor. Transfer any
remaining fuel into an approved container.
Remove and discard the old O-rings. Fuel
can also be drained prior to bowl removal by
loosening/removal of the bowl drain screw. See
Figure 5-18.

Fuel Bowl

Bowl Drain Screw

Figure 5-18. Fuel Bowl Removed From Carburetor.

NOTE: Further disassembly of the fuel bowl is not

necessary unless the Fuel Solenoid Kit, or
Fuel Bowl Kit (obtained separately), will also
be installed.

2. Remove the

fl

oat pin screw and li

ft

out the old

fl

oat, pin, and inlet needle. See Figure 5-19.

Discard all the old parts. The seat for the inlet
needle is not serviceable, and should not be
removed.

Float

Inlet
Needle

Figure 5-19. Removing Float and Inlet Needle.

3. Use an appropriate size

fl

at screwdriver, and

carefully remove the two main jets from the
carburetor. Note and mark the jets by location for
proper installation. The main jets may be size/
side speci

fi

c. A

ft

er the main jets are removed, the

main nozzles can be removed out through the
bo

tt

om of the main towers. Note the orientation/

direction of the nozzles. The end with the two
raised shoulders should be out/down adjacent
to the main jets. Save the parts for cleaning and
reuse. See Figure 5-20.

Main Nozzles

Main Jets

Figure 5-20. Main Jets and Nozzles Removed.

4. Remove the screw securing the

fl

at washer and

ground lead (if equipped), from the top of the
carburetor; then carefully pull (li

ft

) out the two

slow jets. The slow jets may be sized/side speci

fi

c.

Mark or tag the jets for proper reassembly. Note
the small O-ring on the bo

tt

om of each jet. See

Figure 5-21 and 5-22. Save parts for cleaning and
reuse unless a Jet Kit is also being installed. Clean
the slow jets using compressed air. Do not use
wire or carburetor cleaner.

Figure 5-21. Removing Screw and Washer.

«
...
38
39
40
41
42
...
»

Содержание Comand Pro CH1000















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Comand Pro CH1000

Бренд: VEM Страницы: 16

Бренд: DLA Страницы: 7

Бренд: RenewAire Страницы: 28

Бренд: Yanmar Страницы: 160

Бренд: Agrimate Страницы: 32

ARO AF1060 Series

Бренд: Ingersoll-Rand Страницы: 8

Бренд: Ingersoll-Rand Страницы: 8

Бренд: Ingersoll-Rand Страницы: 8

Бренд: Ingersoll-Rand Страницы: 8

Бренд: Tomahawk Страницы: 20

Бренд: Yanmar Страницы: 263

Бренд: Marine Power Страницы: 56

Бренд: Xtreme Power Страницы: 42

45 - V1.0 ASSEMBLY EXHAUSTS 3212I

Бренд: MVVS Страницы: 1

Бренд: ePropulsion Страницы: 46

1941 4-cylinder engine

Бренд: Ford Страницы: 25

Бренд: Eurotherm Страницы: 34

Бренд: 3W Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды