Kohler Comand Pro CH1000 Скачать руководство пользователя страница 122

Страница: 122 / 142

10.12

Section 10
Reassembly

Assemble Cylinder Heads

Prior to installation, lubricate all components with
engine oil, paying particular a

ention to the lip of the

valve stem seal, valve stems, and valve guides. Install
the following items in the order listed below using a
valve spring compressor. See Figures 10-45 and 10-46.

  •  Intake and exhaust valves
  •  Valve spring retainers
•  Valve springs
  •  Valve spring keepers
  •  Valve stem seals

Valve

Spring

Retainer

Keepers

Figure 10-45. Valve Components.

Figure 10-46. Installing Valves with Valve Spring
Compressor.

Install Cylinder Heads

1. Check to make sure there are no nicks or burrs

on the sealing surfaces of the cylinder head or the
crankcase.

2. Check that the dowel pins are in place in the two

lower locations, and install a new cylinder head
gasket, (printed side up). See Figure 10-47.

Figure 10-47. Installing New Head Gaskets.

NOTE: Match the numbers embossed on the cylinder

heads and crankcase. See Figure 10-43.

3. Install the cylinder head. Make sure the head is

at on the gasket and dowel pins. Install a

washer on the screws in

locations 1 and 3

. Install

the spacer followed by a

at washer on the screw

in location 5

. See Figures 10-48 and 10-50. Start

the

ve hex

ange screws.

Spacer

Washer
Locations

Figure 10-48. Washers and Spacer Locations.

4. Torque the hex

ange screws in two stages;

rst to

22.6 N·m (200 in. lb.)

nally to

45.2 N·m

(400 in. lb.)

, following the sequence in Figure

10-50.

5. Repeat the procedure for the opposite cylinder.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды