Kohler Comand Pro CH1000 Скачать руководство пользователя страница 37

Страница: 37 / 142

5.7

Section 5

Fuel System and Governor

Figure 5-7. Governor Springs Installed.

Figure 5-8. Checking Spring Looseness.

3. Hold the governor lever away from the

carburetor so the thro

le lever is against the idle

speed (RPM) adjustment screw of the carburetor.
Start the engine and allow to warm up, then
adjust the screw to set approximately

1200 RPM

Check using a tachometer. Turn the adjustment
screw (inner) clockwise (in) to increase or
counterclockwise (out) to decrease speed.

4. Release the governor lever and check that the

thro

le lever is in the idle (centered) position.

See Figure 5-9. Turn the governed idle (outer)
adjustment screw to obtain the equipment
manufacturer’s recommended idle speed

(1500-1800 RPM)

. The governed idle speed

(RPM) is typically 300 RPM (approximate) higher
than the low idle speed. See Figure 5-10.

Figure 5-9. Throttle Lever in Idle Position.

Figure 5-10. Setting Governed Idle Speed RPM
(Air Cleaner Removed For Clarity).

5. Move the thro

le lever to the wide-open/full

thro

le position and hold in this position. Check

the RPM using a tachometer. Turn the high speed
screw to obtain the intended high speed no-load
RPM.

The governed idle speed must be set

before making this adjustment.

See Figure 5-11.

Governed Idle

Governed Idle
Spring

Spring

Governor

Governor
Spring

Spring

Hold/Pull Governor

Hold/Pull Governor
Lever Back

Lever Back

Governor Spring Must

Governor Spring Must
Be Loose In Slot

Be Loose In Slot

Governed Idle Speed

Governed Idle Speed
Adjustment Screw

Adjustment Screw

High Speed(RPM)
Adjustment Screw

High Speed

High Speed
Adjustment

Adjustment
Screw

Screw

Full Throttle
Position

Figure 5-11. Setting High Speed RPM (Air Cleaner
Removed for Clarity).

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды