Kohler Comand Pro CH1000 Скачать руководство пользователя страница 102

Страница: 102 / 142

Section 9
Inspection and Reconditioning

9.6

Normal:

Even a

er long hours of operation a valve

can be reconditioned and reused if the face and
margin are in good shape. If a valve is worn to where
the margin is less than 1/32 in. do not reuse it. The
valve shown was in operation for almost 1000 hours
under controlled test conditions.

Bad Condition:

The valve depicted here should be

replaced. Note the warped head; margin damaged
and too narrow. These conditions could be a

ributed

to excessive hours or a combination of poor operating
conditions.

Leakage:

A poor grind on face or seat of valve will

allow leakage resulting in a burned valve on one side
only.

Coking:

Coking is normal on intake valves and is not

harmful. If the seat is good, the valve could be reused
a

er cleaning.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Kohler Comand Pro CH1000, Руководство по обслуживанию, Страница: 102 / 142

Результаты поиска

Содержание Comand Pro CH1000

Отзывы: