Kohler Comand Pro CH1000 Скачать руководство пользователя страница 120

Страница: 120 / 142

10.10

Section 10
Reassembly

Install Breather Assembly

1. Make sure the sealing surfaces of the crankcase

and breather cover are clean and free of any
nicks or burrs.

Do not

scrape the surfaces, as this

could result in leakage. Install the four breather
mounting studs into the crankcase if removed
during disassembly.

2. Install the breather chamber gasket as shown.

See Figure 10-38. Assemble and install breather
assembly components as illustrated in Figure
10-39. Make sure the

lter does not extend above

top surface and all parts are properly aligned.

Figure 10-38. Breather Chamber and Gasket.

Figure 10-39. Breather Assembly Details.

Breather Hose

Flange Nuts (4)

Breather

Gasket

Screw

Baffl e

Filter

Adapter

Gasket

Studs (4)

Filter Must
Not Extend
Above
Casting

Filter

Studs (4)

Used on Serial No. 37070xxxxx and Below

Used on Serial No. 37071xxxxx and Higher

Breather Hose

Flange Nuts (4)

Breather

Gasket

Adapter

3. Install the M5 hex

ange nuts onto the studs, then

torque using the sequence shown in Figure 10-40
to

5.7 N·m (51 in. lb.)

Figure 10-40. Breather Assembly Fastener Torque
Sequence.

4. Lightly oil the lower end of the breather hose and

install into the hole in the breather assembly. The
cover should be situated between the two raised
rings of the hose.

Содержание Comand Pro CH1000















































































































































Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды

Kohler Comand Pro CH1000, Руководство по обслуживанию

Результаты поиска

Содержание Comand Pro CH1000

Отзывы:

Похожие инструкции для Comand Pro CH1000

Бренды по названию

Популярные бренды