background image

User

s Manual   

For

DM422 

Fully Digital Stepping Driver

 

Attention: Please read this manual carefully before using the driver! 

The

 

content  in  this  manual  has  been  carefully  prepared  and  is  believed  to  be  accurate,  but  no 

responsibility is assumed for inaccuracies. 

Helix Linear  reserves  the  right  to  make  changes  without  further  notice  to  any  products  herein 
to improve reliability,  function  or design.  Helix Linear  does not assume  any  liability  arising  out 
of the application  or  use  of  any  product  or  circuit  described  herein;  neither does it  convey  any 
license under its patent rights of others.  

Helix  Linear's  general  policy  does  not  recommend  the  use  of  its  products  in  life  support  or 
aircraft applications  wherein  a  failure  or  malfunction  of  the  product  may  directly  threaten  life 
or  injury. According  to  Helix Linear's  terms  and  conditions  of  sales,  the  user  of  Helix Linear's 
products  in  life  support  or  aircraft  applications  assumes  all  risks  of  such  use  and  indemnifies 
Helix Linear against all damages. 

©

201

9

 

Helix Linear

 

Technologies. 

All Rights Reserved

 

Содержание DM422



















Отзывы: