HELIX DM422 Скачать руководство пользователя страница 17

Страница: 17 / 18

DM422 Digital Stepping Drive Manual V1.0

Toll Free 1-855-435-4958

Figure 26: 1

Anti -Resonance Tuning (Speed=0.98rps)

Err_check

Error Check

: This window shows both the present status of each error event and their history.

Current error event(s) can be reset by clicking

Erase Current Err!

button, and all error events

can be reset by clicking

Erase All!

button. List of the last ten drive faults. #0 being the most

recent, #9 is the oldest. See Figure 27.

Figure 27: Error check window

DM422 Digital Stepping Drive Manual V1.0

Toll Free 1-855-435-4958

OverCurrent:

Over-current Protection

. Protection will be activated when continuous current

exceeds 16A.

OverVoltage: Over-voltage Protection

. When power supply voltage exceeds 42

1 VDC, protection

will be activated.

PhaseErr:

Phase Error Protection

. Motor power lines wrong & not connected will activate this

protection.

ErrCounter:

Displays current error(s) and current error history.

Erase Current Err!: Erase Current Err

button. The user can clear current error(s) by clicking this

button.

Erase All!: Erase All!

button. The user can clear all error(s) including error history by clicking this

button.

Web Site: www.helixlinear.com

Web Site:

www.helixlinear.com

Содержание DM422



















Результаты поиска

Содержание DM422

Отзывы:

Похожие инструкции для DM422

Бренды по названию

Популярные бренды

HELIX DM422, Руководство пользователя

Результаты поиска

Содержание DM422

Отзывы:

Похожие инструкции для DM422

Бренды по названию

Популярные бренды