Isuzu NHR 4J Series Скачать руководство пользователя страница 318 | Manualshive

Страница: 318 / 406

background image

ENGINE FUEL 6C - 59

INSPECTION

Check the following items, and replace the control cable if
any abnormality is found.
•

The control cable should move smoothly.

•

The control cable should not be bent or kinked.

•

The control cable should be free of damage and
corrosion.

INSTALLATION

4. Accelerator Control Cable

•

Take care that the core wire of the cable does not get
damaged or kinked.

•

Pull the cable through the grommet hole from under
the floor.

•

Set the groove of the grommet securely into the floor
panel.

•

Lower the cab.

3. Accelerator Control Wire (Accelerator pedal side)

•

Connect the accelerator control wire to the accelerator
pedal.

•

Check to see if the idling control knob is fully turned to
the left.

•

Tilt up the cab.

2. Accelerator Control Wire (Injection pump side)

•

Install the tip end of the wire to the engine control
lever.

1. Lock Bolt

•

With the accelerator control lever attached to the
stopper bolt, pull the cable lightly toward the front of
the axis and fasten the cable bracket with the lock bolt.

•

Check to see if the injection pump lever is at the idle
position (with the lever in touch with the stopper bolt).

•

Connect the battery ground cable.

•

Lower the cab.

•

Check to see if the accelerator pedal play is in the
range of 5 ~ 10 mm above the pedal pad.

•

Press down on the accelerator pedal fully, and check
to see if the engine rotates at the maximum speed with
the linkage in the smooth operation.

•

In the operating range of the accelerator pedal, check
to see if the accelerator pedal and the injection pump
lever return without fail to their original positions
respectively.

6C-58-1.tif

6C-58-2.tif

«
...
316
317
318
319
320
...
»

Содержание NHR 4J Series























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NHR 4J Series

Бренд: ZF Страницы: 28

Бренд: Lombardini Страницы: 88

Бренд: RADEMACHER Страницы: 88

Бренд: MAG Страницы: 13

Бренд: Toro Страницы: 96

Бренд: FIAMA Страницы: 7

Бренд: Wilesco Страницы: 2

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 4

Бренд: YS Страницы: 2

EPA04 Series 40

Бренд: Detroit Diesel Страницы: 158

ZA top SM225.40B

Бренд: ZIEHL-ABEGG Страницы: 76

Бренд: PYD Electrobombas Страницы: 36

Бренд: Honda Страницы: 15

Бренд: Honda Страницы: 60

Бренд: Toyota Страницы: 138

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды