manualshive.com logo in svg

Isuzu NHR 4J Series, Руководство по ремонту, Страница: 341 / 406

Поделиться
Скачать
Isuzu NHR 4J Series Скачать руководство пользователя страница 341

6D2 – 8  STARTING SYSTEM

INSPECTION AND REPAIR

Make necessary correction or parts replacement if wear,
damage or any other abnormal condition are found
through inspection.

ARMATURE

Check the commutator for run-out and replace if the
amount of run-out exceeds the limit.
Run-out test

mm (in.)

kw

Standard

Limit

2.2

2.0

0.02 (0.0008)

0.05 (0.0020)

Check the mica segment for wear.
Depth of mica segment

mm (in.)

kw

Standard

Limit

2.2

2.0

0.7 - 0.9 (0.028 - 0.035)

0.20 (0.008)

Check the commutator outer diameter.
Commutator outer diameter

mm (in.)

kw

Standard

Limit

2.2

2.0

35.00 (1.378)

34.00 (1.339)

Armature short circuit test

Check the armature for short circuit by placing it on a
growler tester.  Hold a piece of hacksaw blade against the
armature core while slowly rotating the armature.  A short-
circuited armature will cause the blade to vibrate and to be
attracted by the core.  If the hacksaw blade is attracted or
vibrates, the armature, is short circuited, and must be
replaced.

6D2-8-1.tif

6D2-8-2.tif

6D2-8-3.tif

6D2-8-4.tif

Содержание NHR 4J Series























































































































































































































































































































































































































Отзывы:

Нет отзывов