Isuzu NHR 4J Series Скачать руководство пользователя страница 177

Страница: 177 / 406

6A1 – 42 4JB1/4JB1T/4JB1TC/4JG2 - ENGINE

4JG2 Cylinder Head Gasket Thickness

mm (in)

Gasket Grade Mark

Piston

Projection

Gasket Thickness

(Reference)

0.658 - 0.713

(0.026 - 0.028)

1.60

(0.0630)

0.713 - 0.759

(0.028 - 0.030)

1.65

(0.0650)

0.759 - 0.814

(0.030 - 0.032)

1.70

(0.0670)

NOTE:

The difference between the highest measured piston
head projection and the lowest measured piston head
projection must not exceed 1.0 mm (0.039 in).

19. Cylinder Head Assembly

1) Install the dowel in cylinder block.
2) Install the cylinder head gasket with top mark up.
3) Clean up cylinder head lower surface and cylinder

body upper surface.

4) Install the cylinder head as softly.
5) Apply engine oil to screw and seat of cylinder head

bolts.

6) Tighten the cylinder head bolts to the specified torque

in three steps following the numerical order shown in
the illustration.

Cylinder Head bolts Torque

∙

m (kg

∙

m/lb

∙

ft)

1st Step

2nd Step

3rd Step

49 (5.0/36)

60 - 75°

18. Push Rod

•

Apply engine oil to push rod and in to the cylinder
head.

17. Rocker Arm shaft

1) Loosen all adjusting screws.
2) Position the rocker arm shaft with the large oil hole

(4ø) facing the front of the engine.

6A1-42-1.tif

6A1-42-2.tif

6A1-42-3.tif

Содержание NHR 4J Series























































































































































































































































































































































































































Результаты поиска

Содержание NHR 4J Series

Отзывы:

Похожие инструкции для NHR 4J Series

Бренды по названию

Популярные бренды

Isuzu NHR 4J Series, Руководство по ремонту

Результаты поиска

Содержание NHR 4J Series

Отзывы:

Похожие инструкции для NHR 4J Series

Бренды по названию

Популярные бренды