Isuzu NHR 4J Series Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 406

background image

GENERAL ENGINE MECHANICAL 6A – 51

4JG2

mm (in)

Standard

Limit

1st

0.09-0.13

(0.0035 - 0.0051)

Compression
ring

2nd

0.05 - 0.07

(0.0020 - 0.0028)

Oil ring

0.03-0.07

(0.0012-0.0028)

0.15

(0.0059)

Piston pin

Visually inspect the piston pin for cracks, flaws, and other
damage and replace if necessary.
1. Use a micrometer to measure the piston pin outside

diameter in both directions at three different positions.
If the measurement exceed the specified limit the
piston pin must be replaced.

Piston pin outside diameter

mm (in)

Standard

Limit

4JB1 /

4JB1T

4JB1TC

30.995 - 31.000

(1.2202 - 1.2204)

30.970 (1.2190)

4JG2

33.995 - 34.000

(1.3384 - 1.3386)

33.970 (1.3374)

2. Measure the inside diameter of the connecting rod

small end. If the clearance between the small end and
pin does not conform to the specified value, the
connecting rod or bushing and pin must be replaced.

mm (in)

Standard

Limit

Clearance

0.008 - 0.020

(0.0003 - 0.0008)

0.05

(0.0020)

3. Insert the piston pin into the piston and rotate it. If the

pin rotates smoothly with no backlash, the clearance is
normal. If there is backlash or roughness, measure the
clearance. If the clearance exceeds the specified limit,
the piston and the piston pin must be replaced.

mm (in)

Standard

Limit

Clearance

0.002 - 0.004

(0.00008 - 0.00016)

0.04

(0.0016)

6A-51-1.tif

6A-51-2.tif

«
...
116
117
118
119
120
...
»

Содержание NHR 4J Series























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NHR 4J Series

Бренд: O.S. engine Страницы: 19

Бренд: D+H Страницы: 20

Бренд: Daewoo Страницы: 205

Бренд: Westerbeke Страницы: 112

Бренд: Festo Страницы: 76

Бренд: YS Страницы: 2

Бренд: Honda Страницы: 48

Бренд: Honda Страницы: 80

Бренд: Volvo Penta Страницы: 122

Бренд: Motion Страницы: 92

Бренд: V2 Страницы: 16

PS01-37x120F-HP-SSC-R/ FC

Бренд: LinMot Страницы: 40

2232***BX4 series

Бренд: Faulhaber Страницы: 60

Бренд: Briggs & Stratton Страницы: 179

Бренд: MVVS Страницы: 6

Бренд: MVVS Страницы: 7

Бренд: Lehman Страницы: 29

Power 160 Brushless Outrunner

Бренд: E-FLITE Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды