Isuzu NHR 4J Series Скачать руководство пользователя страница 359

Страница: 359 / 406

6D3 – 14 CHARGING SYSTEM

VACUUM PUMP

Visual check

•

Inspect the following parts for wear, damage or other
abnormal conditions.

Disassembly of Vacuum pump

•

For the center plate, rotor and vane in the mentioned.

Housing

•

Measure the inside diameter of housing and place if it
exceed the standard.

mm (in)

Standard

57.0 - 57.1

(2.244 - 2.248)

Vane

Measure the length of vanes

mm (in)

Standard

12.5 - 13.5 (0.492 - 0.531)

Check Valve

1. Apply a light pressure onto the "B" side of valve with a

screw driver and check that valve operates smoothly.

2. Apply compressed air 1 - 5 kg/cm

onto "A" side of

valve and check if there is air leak.

Reassembly of vacuum pump

1. Position the rotor, with the serrated boss turned up, on

the center plate and housing.
Align the holes in center plate and rotor.

2. Install vanes into slits in rotor.

The vanes should be installed with chamfered side
turned outward.

3. Install the O-ring and center plate

6D3-14-1.tif

6D3-14-2.tif

6D3-14-3.tif

6D3-14-4.tif

Содержание NHR 4J Series























































































































































































































































































































































































































Результаты поиска

Содержание NHR 4J Series

Отзывы:

Похожие инструкции для NHR 4J Series

Бренды по названию

Популярные бренды

Isuzu NHR 4J Series, Руководство по ремонту

Результаты поиска

Содержание NHR 4J Series

Отзывы:

Похожие инструкции для NHR 4J Series

Бренды по названию

Популярные бренды