Isuzu NHR 4J Series Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 406

background image

6A – 44

GENERAL ENGINE MECHANICAL

10) Crankshaft Timing Gear

!

Install the camshaft timing gear to the camshaft.
The timing gear mark (“Y – Y”) must be facing
outward.

"

Tighten the timing gear to the specified torque.

N

∙

m (kg

∙

m/lb

∙

ft)

64 (6.5/47)

9) Idle Gear

!

Apply engine oil to the idle gear and the idler gear
shaft.
The idler shaft oil hole must be facing up.

"

Position the idler gear setting marks “X” and “Y” so
that they are facing the front of the engine.

#

Align the idler gear “X” setting mark with the
crankshaft timing gear

!

“X – X” setting mark.

$

Align the idler gear “Y” setting mark with the camshaft
timing gear

!

“Y – Y” setting mark.

%

Install the thrust collar and bolts to the cylinder body
through the shaft.
The thrust collar oil hole must be facing up, and the
thrust collar chamfered must be outward.

&

Tighten the idler gear bolt to the specified torque.

N

∙

m (kg

∙

m/lb

∙

ft)

19 (1.9/14)

8) Idler Gear “B” and Shaft

!

Apply engine oil to the idler gear and the idler gear
shaft.

"

Align the idler gear “B”

#

“Z” setting mark with the

idler gear “A”

$

“Z-Z” setting mark.

#

Tighten the idler gear bolt to the specified torque.

N

∙

m (kg

∙

m/lb

∙

ft)

76 (7.7/56)

6A-44-1.tif

6A-44-2.tif

6A-44-3.tif

6A-44-4.tif

«
...
109
110
111
112
113
...
»

Содержание NHR 4J Series























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NHR 4J Series

Electric Motor G2909

Бренд: Grizzly Страницы: 2

Бренд: Kohler Страницы: 12

Бренд: MTU Страницы: 239

Бренд: A'OK Страницы: 7

Бренд: NEUGART Страницы: 2

Бренд: NEUGART Страницы: 2

Бренд: RIB Страницы: 44

Бренд: Quectel Страницы: 39

INline GSI56 e5 Series

Бренд: GEIGER Страницы: 12

Бренд: Yanmar Страницы: 308

Бренд: New Holland Страницы: 41

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: Technosoft Страницы: 34

Бренд: DLE Страницы: 4

MINIMAX 3TNM72-GGE

Бренд: Yanmar Страницы: 2

Бренд: New Holland Страницы: 41

Бренд: ZIEHL-ABEGG Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды