Isuzu NHR 4J Series Скачать руководство пользователя страница 130

Страница: 130 / 406

GENERAL ENGINE MECHANICAL 6A – 63

7) Install the piston rings with the piston ring expander.

The compression ring must be set with the 1N, 2N
mark (4JG2) facing up.
Discrimination mark is painted as shown in the
illustration.

8) Use a piston ring replacer to install the three piston

rings.
Piston Ring Replacer:
Install the piston rings in the numerical order shown in
the illustration.

Oil ring

2nd compression ring

1st compression ring

NOTE:

Install the compression rings with the stamped side
facing up.

Insert the expander coil into the oil ring groove so that
there is no gap on either side of the expander coil
before installing the oil ring.

9) Apply engine oil to the piston ring surfaces.
10) Check that the piston rings rotate smoothly in the

piston ring grooves.

11) Position the piston ring gaps as shown in the

illustration.

6A-63-1.tif

6A-63-2.tif

6A-63-3.tif

6A-63-4.tif

Содержание NHR 4J Series























































































































































































































































































































































































































Результаты поиска

Содержание NHR 4J Series

Отзывы:

Похожие инструкции для NHR 4J Series

Бренды по названию

Популярные бренды

Isuzu NHR 4J Series, Руководство по ремонту

Результаты поиска

Содержание NHR 4J Series

Отзывы:

Похожие инструкции для NHR 4J Series

Бренды по названию

Популярные бренды