Isuzu NHR 4J Series Скачать руководство пользователя страница 364

Страница: 364 / 406

CHARGING SYSTEM 6D3 – 19

7. Removal of Bearing (on the Rear Side) [Only for

Replace.]

Take out the bearing with a puller.
Insert it to see whether replacement is needed.

NOTE:

Conduct the bearing inspection mentioned below and
determine whether or not the bearing be replaced.

INSPECTION AND REPAIR

NOTE:

Standard values and limits vary with alternators, and
therefore, maintenance standards for each part
should be followed.

1) Fan

Check to see whether it is deformed.

2) Bearing

Turn it by hand to check for smooth and noiseless
turning.

3) Stator
•

Resistance between phases (neutral point and each
phase lead wire) should be 1

Ω

or less.

•

Insulation resistance between the core and stator coil
should be 0.1M

Ω

or more by a 500V megohmmeter.

NOTE:

If there is no continuity, the connection of lead wire
should be checked as the disconnected stator coil
cannot be considered.

4) Rotor
•

Resistance between slip rings as shows in the
illustration, about 4

Ω

•

Insulation resistance between slip ring and ball core:
0.1M

Ω

or more by 500V megohmmeter.

•

Check slip rings for surface. If staind or rough, use
sand paper (#300 - #500).

6D3-19-1.tif

6D3-19-2.tif

6D3-19-3.tif

Tighten the lightly with
a vise with care not to
cause any damage

Содержание NHR 4J Series























































































































































































































































































































































































































Результаты поиска

Содержание NHR 4J Series

Отзывы:

Похожие инструкции для NHR 4J Series

Бренды по названию

Популярные бренды

Isuzu NHR 4J Series, Руководство по ремонту

Результаты поиска

Содержание NHR 4J Series

Отзывы:

Похожие инструкции для NHR 4J Series

Бренды по названию

Популярные бренды