Isuzu NHR 4J Series Скачать руководство пользователя страница 226

Страница: 226 / 406

4JB1/4JB1T/4JB1TC/4JG2 – ENGINE 6A1 – 91

•

Install the bearing caps with the bearing cap head
arrow mark facing the front of the engine.

•

Apply engine oil to the front of the engine.

•

Tighten the crankshaft bearing cap bolts to the
specified torque a little at a time in the sequence
shown in the illustration.

∙

m (kg

∙

m/lb

∙

ft)

167 (17.0/123)

NOTE:

Check to see that the crankshaft turns smoothly by
rotating it manually.

13. Crankshaft Rear Oil Seal

Use the oil seal installer to install the oil seal to the cylinder
body.
Rear Oil Seal Installer: 5-8840-2361-0

NOTE:

Wipe off rust and scraps clean from the press-in
portion of the oil seal.

Take note of the press-in direction of the oil seal.

1) Install the adapter of the special tool to the rear end of

the crankshaft with two bolts.

2) Install the oil seal to the outer circumference of the

adapter.

3) Insert the slave into the adapter portion, and tighten it

in with the bolt (M12x1.75L=70) until the adapter
section hits the slave.

4) Remove the adapter and the slave.
5) After installing the oil seal, check the measurement of

the oil seal.

Standard

mm (in)

12.2 - 12.8 (0.48 - 0.50)

12. Flywheel and Cylinder Body Rear Plate

•

Align the rear plate with the cylinder body knock pins.

•

Tighten the rear plate to the specified torque.

Rear Plate Bolts Torque

∙

m (kg

∙

m/lb

∙

ft)

82 (8.4/61)

6A1-91-1.tif

6A1-91-2.tif

6A1-92-3.tif

Содержание NHR 4J Series























































































































































































































































































































































































































Результаты поиска

Содержание NHR 4J Series

Отзывы:

Похожие инструкции для NHR 4J Series

Бренды по названию

Популярные бренды

Isuzu NHR 4J Series, Руководство по ремонту

Результаты поиска

Содержание NHR 4J Series

Отзывы:

Похожие инструкции для NHR 4J Series

Бренды по названию

Популярные бренды