Isuzu NHR 4J Series Скачать руководство пользователя страница 267

Страница: 267 / 406

6C - 8 ENGINE FUEL

FUEL FILTER CARTRIDGE

REMOVAL

•

Remove the cartridge using a filter wrench.
Filter wrench: 5-8840-0253-0 (J-22700)

INSTALLATION

•

Clean the cartridge mounting surface of filter body so
that the cartridge can be securely.
Apply engine oil thinly to new cartridge O-ring.

•

To facilitate bleeding, fill the new cartridge with light oil.

•

Tighten the cartridge until O-ring comes in contact with
the sealing, taking care not to spill the light oil.

•

Retighten 1/3~ 2/3 using a filter wrench.

Filter wrench: 5-8840-0253-0 (J-22700)

Bleeding

•

Operate priming pump to send the air in the fuel
system to the injection pump.

•

Loosen injection pump bleeding plug, and operate the
priming pump until no bubble is made.

•

Tighten the bleeding plug.

•

Start the engine, and if it is not started in 10 seconds
or less, repeat the bleeding steps.

•

Make sure of no fuel leakage, and tighten the priming
pump.

Draining

•

When the water in the sedimentor reaches the
specified volume, warning light is actuated.
In this case, follow the draining steps below.

•

Set a vinyl hose over the drain plug.

•

Loosen the drain plug.

•

To drain the water, operate the priming pump several
times.

•

After draining, tighten the drain plug.

•

Operate the priming pump several times to check for
fuel leakage.

•

Check and see the warning light is off.

6C-7-2.tif

6C-7-1.tif

Содержание NHR 4J Series























































































































































































































































































































































































































Результаты поиска

Содержание NHR 4J Series

Отзывы:

Похожие инструкции для NHR 4J Series

Бренды по названию

Популярные бренды

Isuzu NHR 4J Series, Руководство по ремонту

Результаты поиска

Содержание NHR 4J Series

Отзывы:

Похожие инструкции для NHR 4J Series

Бренды по названию

Популярные бренды