Isuzu NHR 4J Series Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 406

background image

SERVICE INFORMATION 00 – 47

Adjust the No. 1 or the No. 4 cylinder valve clearance
while their respective cylinders are at TDC on the
compression stroke.

Valve Clearance (At Cold)

mm (in)

0.4 (0.016)

4. Loosen each valve clearance adjusting screw as

shown in the illustration.

5. Insert a feeler gauge of the appropriate thickness

between the rocker arm and the valve stem end.

6. Turn the valve clearance adjusting screw until a slight

drag can be felt on the feeler gauge.

7. Tighten the lock nut securely.
8. Rotate the crankshaft 360°.
9. Realign the crankshaft damper pulley TDC notched

line with the timing pointer.

10. Adjust the clearance for the remaining valves as

shown in the illustration.

INJECTION TIMING ADJUSTMENT

1. Check that the notched line on the injection pump

flange is aligned with the front plate or the timing gear
case notched line.

2. Bring the piston in the No.

!

cylinder to TDC 1 on the

compression stroke by turning the crankshaft until the
crankshaft pulley TDC line is aligned with the timing
mark

"

.

Note:

Check for play in the No. 1 intake and exhaust valve
push rods.
If the No. 1 cylinder intake and exhaust valve push
rods have play, the No. 1 piston is at TDC on the
compression stroke.

3. Disconnect the injection pipe from the injection pump.
4. Remove one bolt from the distributor head.
5. Insert a screwdriver into a hole in the fast idle lever

and turn the lever to release the W-C.S.D. function. (If
so equipped)

6. Install the static timing gauge

#

.

The probe of the gauge should be depressed inward
approximately 2 mm (0.079 in).
Static Timing Gauge : 5-8840-0145-0 (J-28827)

0046-1.tif

0046-2.tif

0046-3.tif

0046-4.tif

0046-5.tif

«
...
49
50
51
52
53
...
»

Содержание NHR 4J Series























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NHR 4J Series

Vickers M2-200 Series

Бренд: Eaton Страницы: 13

Бренд: WÄRTSILÄ Страницы: 232

Бренд: Hyster Страницы: 25

Бренд: TYROLIT Hydrostress Страницы: 19

Air Cooled TR-10D

Бренд: Wisconsin Страницы: 46

Бренд: Shindaiwa Страницы: 48

AG2210-LP Series

Бренд: Beckhoff Страницы: 35

Бренд: FIAMA Страницы: 7

Бренд: KAZZ Страницы: 11

Бренд: Yanmar Страницы: 280

Бренд: Wood-mizer Страницы: 146

Бренд: Honda Страницы: 28

Бренд: M.T.H. Страницы: 23

Бренд: Toyota Страницы: 185

Бренд: Desert Aircraft Страницы: 20

Бренд: JAC Страницы: 14

Бренд: Grundfos Страницы: 12

Бренд: Farymann Diesel Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды