Isuzu NHR 4J Series Скачать руководство пользователя страница 104

Страница: 104 / 406

GENERAL ENGINE MECHANICAL 6A – 37

12. Main Bearing Cap

•

Apply the recommended liquid gasket or its equivalent
to the No. 5 crankshaft bearing cap

as shown in the

illustration.

•

Install the arch gasket

to the No. 5 bearing cap.

Use your fingers to push the arch gasket into the
bearing cap groove.

NOTE:

Be sure that the bearing cap fitting surface is
completely free of oil before applying the liquid
gasket.

Do not allow the liquid gasket to obstruct the cylinder
thread holes and bearings.

•

Install the bearing caps with the bearing cap head
arrow mark facing the front of the engine.

•

Apply engine oil to the crankshaft bearing cap bolts.

•

Tighten the crankshaft bearing cap bolts to the
specified torque a little at a time in the sequence
shown in the illustration.

∙

m (kg

∙

m/lb

∙

ft)

167 (17.0/123)

NOTE:

Check to see that the crankshaft turns smoothly by
rotating it manually.

6A-37-1.tif

6A-37-2.tif

6A-37-3.tif

Содержание NHR 4J Series























































































































































































































































































































































































































Результаты поиска

Содержание NHR 4J Series

Отзывы:

Похожие инструкции для NHR 4J Series

Бренды по названию

Популярные бренды

Isuzu NHR 4J Series, Руководство по ремонту

Результаты поиска

Содержание NHR 4J Series

Отзывы:

Похожие инструкции для NHR 4J Series

Бренды по названию

Популярные бренды