manualshive.com logo in svg

Isuzu NHR 4J Series, Руководство по ремонту

Workshop Manual для Isuzu NHR 4J Series доступен для бесплатного скачивания на нашем сайте. Пользователи могут легко загрузить данный manual и ознакомиться с подробной информацией о техническом обслуживании и ремонте автомобиля. Скачайте его сейчас на manualshive.com.

Поделиться
Скачать
background image

6C - 28  ENGINE FUEL

INSTALLATION

14. Injection Pump Assembly

1. Timing gear case a camshaft timing gear side c

injection pump timing gear side check holde cover.

2. Turn the crankshaft clockwise to see the TDC mark of

the crank pulley to the pointer, and then bring the No.
1 cylinder to the TDC on the compression stroke.

3. Look in through the check hole on the crankshaft

timing gear side and check to see if the “O” mark on
the timing gear is in line with the pointer of the check
hole.

4. In the condition above with the injection pump gear

mark “O” set to the pointer of the check hole, install
the injection pump assembly.

•

Install the injection pump fixing bolts and tighten them
to the specified torque.

Pump Bolts Torque

N

∙

m (Kg

∙

m/lb

∙

ft)

                                                                                                                   

15 (1.5/11)

                                                                                                                   

13. Injection Pipe

•

Connect the pump side and nozzle side of the pipe,
and tighten securely.

•

Install clip where it was.

Sleeve Nut Torque

N

∙

m (Kg

∙

m/lb

∙

ft)

                                                                                                                   

29 (3.0/22)

                                                                                                                   

12. Injection Pump Harness

•

Mount engine harness and connect it to switches.

11. CSD Water Hose

•

Connect the water hose and tighten clip securely.

6C-27-1.tif

6C-27-2.tif

6C-27-3.tif

6C-27-4.tif

Содержание NHR 4J Series























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NHR 4J Series

Quectel M10 Hardware Description preview
M10
Бренд: Quectel Страницы: 71
Jabiru 2200 Overhaul Manual preview
2200
Бренд: Jabiru Страницы: 201
Jabiru 2200 Maintenance Manual preview
2200
Бренд: Jabiru Страницы: 103
TAYO ZT1P52MI Maintenance Manual preview
ZT1P52MI
Бренд: TAYO Страницы: 42
SAS RIO Bravo IP Engine User Manual-Preliminary preview
RIO Bravo IP Engine
Бренд: SAS Страницы: 19
NOVAK BALLISTIC Instructions preview
BALLISTIC
Бренд: NOVAK Страницы: 2
Vedeneyev M-14P Maintenance Manual preview
M-14P
Бренд: Vedeneyev Страницы: 381
Mercury Racing 1550 STERNDRIVE Operation, Maintenance & Warranty preview
1550 STERNDRIVE
Бренд: Mercury Racing Страницы: 75
SCREENLINE SL2190 Manual preview
SL2190
Бренд: SCREENLINE Страницы: 4
TecumsehPower HSK600 Operator'S Manual preview
HSK600
Бренд: TecumsehPower Страницы: 24
Tecumseh OHV 135 Operator'S Manual preview
OHV 135
Бренд: Tecumseh Страницы: 20
Tecumseh LEV100 Operator'S Manual preview
LEV100
Бренд: Tecumseh Страницы: 8
Toro GTS 200 Service Manual preview
GTS 200
Бренд: Toro Страницы: 62
Detroit Diesel Series 60 EGR Technician Manual preview
Series 60 EGR
Бренд: Detroit Diesel Страницы: 195
Yanmar D10 Safety, Operation, Maintenance & Parts Manual preview
D10
Бренд: Yanmar Страницы: 32
Tecno Automazione GPS 120 Instructions And Warnings preview
GPS 120
Бренд: Tecno Automazione Страницы: 11
Honda GX120T2 Supplement Manual preview
GX120T2
Бренд: Honda Страницы: 30
Honda GX110 Owner'S Manual preview
GX110
Бренд: Honda Страницы: 41

Бренды по названию

Популярные бренды

Загрузить еще бренды