manualshive.com logo in svg

Isuzu NHR 4J Series, Руководство по ремонту

Workshop Manual для Isuzu NHR 4J Series доступен для бесплатного скачивания на нашем сайте. Пользователи могут легко загрузить данный manual и ознакомиться с подробной информацией о техническом обслуживании и ремонте автомобиля. Скачайте его сейчас на manualshive.com.

Поделиться
Скачать
background image

6A1 – 68  4JB1/4JB1T/4JB1TC/4JG2 - ENGINE

INSTALLATION

7. Camshaft and Tappets

•

Apply a coat of engine oil to the tappet and the cylinder
body tappet insert holes.

•

Locate the position mark applied at disassembly (if the
tappet is to be reused).

NOTE:

The tappet must be installed before the camshaft.

•

Apply a coat of engine oil to the camshaft and the
camshaft bearings.

•

Install the camshaft to the cylinder body.
Take care not to damage the camshaft bearings.

6. Oil Pump Assembly

•

Prepare a solution of 80% engine oil and 20%
molybdenum disulfide.

•

Apply and ample coat of the solution to the teeth of the
oil pump pinion.

•

Apply engine oil to oil pipe O-ring and insert the O-ring
in O-ring hold on cylinder block.

•

Install oil pump asm with oil pipe in cylinder block and
tighten fixing bolts to the specified torque.

Oil Pump Bolt Torque

N

∙

m (kg

∙

m/lb

∙

ft)

                                                                                                                   

19 (1.9/14)

                                                                                                                   

•

Tighten sleeve nut to the specified torque.

Sleeve Nut Torque

N

∙

m (kg

∙

m/lb

∙

ft)

                                                                                                                   

25 (2.5/18)

                                                                                                                   

5. Oil Pan Assembly

Above works refer to “OIL PAN” Section in this manual.

4a. Timing Belt

8) Camshaft timing pulley
7) Timing belt
6) Flange: injection pump pulley
5) Flange: camshaft pulley
4) Timing pulley lower cover
3) Timing pulley upper cover
2) Crankshaft damper pulley
1) Cooling fan assembly

Above works refer to “TIMING BELT (Belt Type)”
Section in this manual.

6A1-68-1.tif

6A1-68-2.tif

Содержание NHR 4J Series























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NHR 4J Series

VAR-SPE K4 Instructions Manual preview
K4
Бренд: VAR-SPE Страницы: 80
S&C Pad-Mounted Series Installation And Operation Manual preview
Pad-Mounted Series
Бренд: S&C Страницы: 15
TOPMAQ BL-260A Manual preview
BL-260A
Бренд: TOPMAQ Страницы: 17
M.T.H. Premier U30C Operator'S Manual preview
Premier U30C
Бренд: M.T.H. Страницы: 26
BRP Rotax 125 JUNIOR MAX evo Repair Manual preview
Rotax 125 JUNIOR MAX evo
Бренд: BRP Страницы: 174
BRP EVINRUDE E-TEC BE225HGXABA Manual preview
EVINRUDE E-TEC BE225HGXABA
Бренд: BRP Страницы: 356
SSANGYONG D20DTF Information preview
D20DTF
Бренд: SSANGYONG Страницы: 16
SSANGYONG 0000-00 User Manual preview
0000-00
Бренд: SSANGYONG Страницы: 42
RADEMACHER RolloTube S-line Sun DuoFern Brief Instructions For Installation And Initial Commissioning preview
RolloTube S-line Sun DuoFern
Бренд: RADEMACHER Страницы: 2
Fagor FKM1 Series Installation Manual preview
FKM1 Series
Бренд: Fagor Страницы: 174
Detroit Diesel Series 60 DDEC VI Troubleshooting Manual preview
Series 60 DDEC VI
Бренд: Detroit Diesel Страницы: 402
DERRICK HYPERPOOL SHAKER Maintenance & Operation Manual preview
HYPERPOOL SHAKER
Бренд: DERRICK Страницы: 118
Honda GC Series Information preview
GC Series
Бренд: Honda Страницы: 8
Honda G35 Owner'S Manual preview
G35
Бренд: Honda Страницы: 2
Honda CR250R Owner'S Manual & Competition Handbook preview
CR250R
Бренд: Honda Страницы: 149
DLE DLE35RA User Manual preview
DLE35RA
Бренд: DLE Страницы: 4
vds 100034/09E Technical Installation Manual preview
100034/09E
Бренд: vds Страницы: 49
DERRICK EX Maintenance & Operation Manual preview
EX
Бренд: DERRICK Страницы: 38

Бренды по названию

Популярные бренды

Загрузить еще бренды