manualshive.com logo in svg

Isuzu NHR 4J Series, Руководство по ремонту

Workshop Manual для Isuzu NHR 4J Series доступен для бесплатного скачивания на нашем сайте. Пользователи могут легко загрузить данный manual и ознакомиться с подробной информацией о техническом обслуживании и ремонте автомобиля. Скачайте его сейчас на manualshive.com.

Поделиться
Скачать
background image

6B - 8  ENGINE COOLING

INSTALLATION

9. Water Pump Assembly

•

Set O-ring in water pump body groove.

•

Install water pump assembly, and tighten to specified
torque.

Pump Fixing Bolt Torque

N

∙

m (Kg

∙

m/lb

∙

ft)

                                                                                                                  

20 (2.0/14)

                                                                                                                  

8. Timing Pulley Lower Cover

•

Install timing pulley lower cover, and tighten to
specified torque.

Cover Fixing Bolts Torque

N

∙

m (Kg

∙

m/lb

∙

in)

                                                                                                                  

8 (0.8/69)

                                                                                                                  

7. Timing Pulley Upper Cover

•

Install timing upper cover, and tighten to specified
torque.

Cover Fixing Bolts Torque

N

∙

m (Kg

∙

m/lb

∙

in)

                                                                                                                  

8 (0.8/69)

                                                                                                                  

6. Crankshaft Damper Pulley

•

Install crankshaft damper pulley, and tighten to
specified torque.

Pulley Bolt Torque

N

∙

m (Kg

∙

m/lb

∙

in)

                                                                                                                  

19 (1.9/14)

                                                                                                                  

5. AC Generator Drive Belt

4. A/C Compressor Drive Belt

3. Power Steering Pump Drive Belt

•

Install the drive belts and adjust belt
Check drive belts for wear or damage, and replace
with new ones as necessary. Check belts for tension,
and adjust as necessary.

•

Push the middle of belts with a force of 98 N
(10 kg/22 lb) and check each bolt for deflection.

•

Standard deflection

mm (in)

Initial tension

AC Generator drive belt
A/C compressor drive belt
Power Steering drive belt

8 – 12

(0.31-0.47)

6B-7-1.tif

6B-7-3.tif

6B-7-2.tif

Содержание NHR 4J Series























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NHR 4J Series

Eaton 1 Series Repair Information preview
1 Series
Бренд: Eaton Страницы: 32
Simple Motors Kit 5 Assembly Instructions Manual preview
Kit 5
Бренд: Simple Motors Страницы: 10
Oben ALCYO ACCU-TRK-AT Operating Instructions Manual preview
ALCYO ACCU-TRK-AT
Бренд: Oben Страницы: 28
Zundapp 100 cc Service Manual preview
100 cc
Бренд: Zundapp Страницы: 52
Rotax 912 i series Service Instruction preview
912 i series
Бренд: Rotax Страницы: 13
Premier 2-10-4 TEXAS STEAM ENGINE Operating Instructions Manual preview
2-10-4 TEXAS STEAM ENGINE
Бренд: Premier Страницы: 24
Man E 2942 LE 302 Repair Manual preview
E 2942 LE 302
Бренд: Man Страницы: 18
Siemens SIEMOSYN 1FU8 Operating Instructions Manual preview
SIEMOSYN 1FU8
Бренд: Siemens Страницы: 28
Siemens 6FB1203-5AT00-7MP0 Compact Operating Instructions preview
6FB1203-5AT00-7MP0
Бренд: Siemens Страницы: 7
Siemens COMBIMASTER CM110/3 Operating Instructions Manual preview
COMBIMASTER CM110/3
Бренд: Siemens Страницы: 21
Siemens 2KG14 Series Information On Safety And Commissioning preview
2KG14 Series
Бренд: Siemens Страницы: 19
Siemens COMBIMASTER Operating Instructions Manual preview
COMBIMASTER
Бренд: Siemens Страницы: 24
Siemens 2KG13 Information On Safety And Commissioning preview
2KG13
Бренд: Siemens Страницы: 15
Siemens 1PH4 103 Instructions For Use Manual preview
1PH4 103
Бренд: Siemens Страницы: 16
Siemens CAZBHS Installation Operation & Maintenance preview
CAZBHS
Бренд: Siemens Страницы: 38
Siemens 1PA6 Series Instructions Manual preview
1PA6 Series
Бренд: Siemens Страницы: 24
Siemens 1PM103 Instructions Manual preview
1PM103
Бренд: Siemens Страницы: 36
Siemens 1PM4 101 Instructions Manual preview
1PM4 101
Бренд: Siemens Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды