manualshive.com logo in svg

Isuzu NHR 4J Series, Руководство по ремонту, Страница: 274 / 406

Поделиться
Скачать
Isuzu NHR 4J Series Скачать руководство пользователя страница 274

ENGINE FUEL  6C - 15

REASSEMBLY AND OPENING
PRESSURE ADJUSTMENT (4JB1-TC
only)

1. Nozzle holder body
2. Shim (First opening pressure adjustment)
3. First spring
4. Spring seat
5. Collar
6. Second spring
7. Push rod
8. Shim (Second opening pressure adjustment)
9. Spring seat
10. Lift piece
11. Spacer & pin
12. Nozzle & pin
13. Retaining nut
14. Gasket
15. Eye bolt

The nozzle holder is adjusted as the components are
reassembled in the sequence above.
As adjustment of the two-spring nozzle holder is made in
hundredths of a millimeter, clean the parts thoroughly in light oil
to completely remove any dirt or foreign matter.

REASSEMBLY AND ADJUSTMENT PROCEDURE

1

First nozzle opening pressure adjustment

Adjust the first nozzle opening pressure using the shim.

2

Full needle valve lift confirmation

Confirm the full needle valve lift in accordance with the
closed method.

3

Pre-lift confirmation

Confirm pre-lift in accordance with the closed method.

CAUTION:

If not as specified, replace the nozzle assembly, lift
piece, pins and spacer using the nozzle service kit.

4

Second nozzle opening pressure

confirmation

Confirm the second nozzle opening pressure in accordance
with the closed method.

5

Second nozzle opening pressure

adjustment

Adjust the second nozzle opening pressure using the shim.

6

Final inspection

Confirm the condition of the fuel spray with the nozzle and
nozzle holder assembled.

080LX003.tif

Содержание NHR 4J Series























































































































































































































































































































































































































Отзывы:

Нет отзывов