Isuzu NHR 4J Series Скачать руководство пользователя страница 332

Страница: 332 / 406

ENGINE ELECTRICAL 6D1 – 7

WARNING:

Never attach the end of the jumper cable directly to
the negative terminal of the dead battery.

5. Start the engine of the vehicle with the good battery.

Make sure that all unnecessary electrical accessories
have been turned "OFF".

6. Start the engine of the vehicle with the dead battery.

7. To remove the jumper cables, follow the above

directions in the reverse order.

Be sure to first disconnect the negative cable from the
vehicle with the discharged battery.

REMOVAL AND INSTALLATION OF THE
BATTERY

REMOVAL

1. All switches should be in the "OFF" position.

2. Disconnect the battery ground cable.

3. Disconnect the battery positive cable.

4. Disconnect the battery cable.

CAUTION:

It is important that the battery ground cable be
disconnected first.

Disconnecting the battery positive cable first can
result in a short circuit.

INSTALLATION

To install the battery, follow the removal procedure in the
reverse order, noting the following points:

1. Make sure that the rod is hooked on the body side.

MAIN DATA AND SPECIFICATIONS

Model

(JIS)

115E41R-MF

130E41R-MF

95D31R-MF

80D26R-MF

Voltage

(V)

Cold-Cranking Performance

(Amp)

651

799

622

582

Reserve Capacity

(Min)

212

229

159

133

Load Test

(Amp)

325

400

310

290

Fast Charge Maximum Amperage

(Amp)

BCI Group No.

Overall Dimension L×W×H

(mm)

410×178×213

6D1-7-1.tif

Содержание NHR 4J Series























































































































































































































































































































































































































Результаты поиска

Содержание NHR 4J Series

Отзывы:

Isuzu NHR 4J Series, Руководство по ремонту, Страница: 332 / 406

Результаты поиска

Содержание NHR 4J Series

Отзывы: