Isuzu NHR 4J Series Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 406

background image

6A – 52

GENERAL ENGINE MECHANICAL

Bushing replacement

Removal:

Use a suitable bar and bench press or
hammer.

Installation: Use a suitable bar and bench press.

NOTE:

Align the bushing with the connecting rod oil port.

After installing a new bushing, finish the bushing bore
with a pin hole grinder.

Connecting rods

1. Check the connecting rod alignment with a connecting

rod aligner.
If either the bend or the twist exceeds the specified
limit, the connecting rod must be replaced.

mm (in)

Standard

Limit

Bend per 100 (3.94) 0.08 (0.0031) or less 0.20 (0.0079)

Twist per 100 (3.94) 0.05 (0.0020) or less 0.15 (0.0059)

2. Measure the connecting rod thrust clearance.

Use a feeler gauge to measure the thrust clearance at
the big end of the connecting rod.
If the clearance exceeds the specified limit, the
connecting rod must be replaced.

Thrust Clearance

mm (in)

Standard

Limit

0.230 (0.0091)

0.350 (0.0138)

3. Measure the oil clearance between the connecting rod

and the crankshaft by:
1) Remove the connecting rod cap nuts and the rod

caps.
Arrange the removed rod caps in the cylinder
number order.

2) Clean the rod bearings and the crankshaft pins.
3) Carefully check the rod bearings.

If even one bearing is found to be damaged or
badly worn, the entire bearing assembly must be
replaced as a set. Reinstall the bearings in their
original positions.
Apply plastigage to the crank pin.

4) Reinstall the rod caps to their original positions

6A-52-1.tif

6A-52-2.tif

6A-52-3.tif

6A-52-4.tif

«
...
117
118
119
120
121
...
»

Содержание NHR 4J Series























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NHR 4J Series

MULTI-VANE 1800 Series

Бренд: Ingersoll-Rand Страницы: 12

Бренд: Lenze Страницы: 20

Бренд: Baldor Страницы: 1

Бренд: Orion Страницы: 4

Бренд: Volvo Penta Страницы: 100

Бренд: Volvo Penta Страницы: 104

Бренд: Toro Страницы: 233

Бренд: YS Страницы: 2

Бренд: Volvo Страницы: 64

Бренд: Winterthur Gas Страницы: 547

Бренд: panthera Страницы: 12

Бренд: Tomahawk Страницы: 20

Бренд: yellow Gardenline Страницы: 64

Бренд: DLE Страницы: 4

Бренд: LinMot Страницы: 48

Бренд: Ford Страницы: 124

Бренд: Vetus Страницы: 100

Бренд: Vetus Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды