Intec MLC 8000 Скачать руководство пользователя страница 46

Страница: 46 / 196

INTEC GmbH

22/12/2016

Lift controller MLC 8000

Operating manual V2.0

46/196

1. Menu level

2. Menu level

3. Menu level

4. Menu level

Description

completely pulled in /pulled out.

- both on: The door close relay remains on after the door is completely

closed; the door open relay remains energized after the door is fully

opened

- both off: Once the holding bolts are completely in / out, the relays are

switched off immediately.

- Out on: The relay to pull out the holding bolts remains energized

even if the holding bolts are completely pulled out and is switched off

not until the holding bolts should be pulled in.

- In on: The relay to pull in the holding bolts remains energized even if
the holding bolts are completely pulled in and is switched off not until

the holding bolts should be pulled out.

- Both on: Both relays remain switched on even if the assigned state is

reached.

In-out[ms]

Delay time between changing the moving direction of holding bolts

(pull in / pull out).

Max.time[s]

Supervision time for pulling in / out the holding bolts. If the bolt doin't

reached attached position the lift controller sets an error message.

Max.Bolt in

Max. Number of attempts to pull in the holding bolt before going out of

operation.

Max.Bolt out

Max. Number of attempts to pull out the holding bolt before going out

of operation.

Errordel[ms]

Debouncing time for the holding bolt contacts to prevent error

messages.

Startdel[ms]

Start delay to move upwards / downwards for handling the holding

bolts.

Bolt if fire

Indicates if the holding bolts must be used in case of fireman

operation.

Floors with Hold

Indicates which floors are equipped with holding bolts.

1. Floor

1st floor is equipped with holding bolts (yes / no)

2. Floor

2nd floor is equipped with holding bolts (yes / no)

...

Deceler.check

Parameter for Slow down supervision when driving into the end floor

v-lim.[mm/s]

speed threshold at which the special exit "v-limit" is turned on or off.

Slow speed

Reduced speed to which delays should be applied when entering the

top or bottom floor (v1 or v2)

Содержание MLC 8000





































































































































































































Результаты поиска

Содержание MLC 8000

Отзывы:

Похожие инструкции для MLC 8000

Бренды по названию

Популярные бренды

Intec MLC 8000, Руководство по эксплуатации

Результаты поиска

Содержание MLC 8000

Отзывы:

Похожие инструкции для MLC 8000

Бренды по названию

Популярные бренды