Intec MLC 8000 Скачать руководство пользователя страница 58

Страница: 58 / 196

INTEC GmbH

22/12/2016

Lift controller MLC 8000

Operating manual V2.0

58/196

1. Menu level

2. Menu level

3. Menu level

4. Menu level

Description

Overl[kg]

Starting this value is detected as overload.

Setting this value to 0, the overload detection is disabled.

Temp.sensor

Settings for temperature sensor on HSE board (only HSE version 1.05

and newer)

Min.temp

Use temperature sensor for checking minimum machine room

temperature

Min.Limit[°C]

Minimum temperature in °C

Max.temp

Use temperature sensor for checking maximum machine room

temperature

Max.Limit[°C]

Maximum temperature in °C

Cooling [°C]

Temperature level to switch on cooling (Special output-cooling; e.g.

for control cabinet fan)

Internal Param.

All red values are system parameters and should be changed only in

exceptional cases by specialists.

Empty load

Analog value of the load sensor in an empty car.

100% load

Analog value of the load sensor with a full car (rated load).

Startpos.

Internal starting value for position count

Count dir.

Counting direction of the position sensor (Encoder)

Doorzone> >SGM

Simulation of the door zone switch by controlling (distance between

the simulated signal SGO and SGU and switching point SGM)

Min.

Doorzone>

Settings for lifts with very short floor distances (<300mm approx): If

the floor distance is less than the this value, then the two floors have a

common door zone; which means, the door zone between the two

floors is not switched off (both "real" door zone switch as well as

simulated by the lift controller or "Double-AWG" door zone switch)

Inc.by accu

Setting if the incremental position encoder is buffered by battery

voltage or not. If set to "No", a new calibration trip (reset trip) takes

place (to the reference switch SGE) if the mains supply was switched
off. If set to "Yes", it is assumed that the incremental encoder counts

up even during a power failure and thus a new calibration run is not

required.

AWG1-2[mm]

In case of usage a "Double AWG" for positioning: distance between

the two position units and thus the difference in the measured

position.

Pos.mode[mm]

Only for operation of a CANopen Lift frequency inverter in "Position

mode": distance from the required braking point when entering a level

in which the targeted floors can still be changed.

Содержание MLC 8000





































































































































































































Результаты поиска

Содержание MLC 8000

Отзывы:

Бренды по названию

Популярные бренды

Intec MLC 8000, Руководство по эксплуатации

Результаты поиска

Содержание MLC 8000

Отзывы:

Бренды по названию

Популярные бренды