Intec MLC 8000 Скачать руководство пользователя страница 139

Страница: 139 / 196

INTEC GmbH

22/12/2016

Lift controller MLC 8000

Operating manual V2.0

139/196

Main function

Sub function/

Direction/

Floor

Doors

Description

Output is activated if lift is moving or door is opened in a floor.

LC request

Output is activated for 1s if a landing call is pressed, while this call

is disabled by any special function.

Drive off

If the lift is not used for a longer timer (see Parameter „Energy

savings“ -> „Drive off[s]“) the drive (e.g. VVVF) may be switched to

standby with this output.

In standby mode the fault signal from the drive is ignored.

Note: The drive should be equipped with a standby input for this

function. However, it is also possible to use this output to switch

off the power supply of the drive.

Door off

Output to switch off the door controller if the lift is not used for a

longer time and the doors are closed (see Parameter "Energy

savings"-> "Door off[s]")

Hazard mode

Output for signaling a „Hazard transport“ (Input „Hazard run“

active)

Hazard call

Output for signaling that a hazard call was pressed.9999

Saf.geartest

Output for automated testing the safety gear (see menu item

"Technical check")

v limit

Programmed speed limit exceeded (see "Special param. -

Deceler.check")

Teach-in

Teach in mode activ

Group off

Output for signaling that group control is deactivated

Cooling

Output for cooling (e.g. control cabinet fan); switched by

temperature sensor on HSE (from hardware version 1.05)

Error outputs Fault signal

General fault output

Safety modul

Fault signal: Error in safety unit

Safety circ.

Fault signal: Safety circuit errornous opened

Door error

Doors

Fault signal: Door error

Overtemp.1

Fault signal: Motor overheated (input overtemperature 1

Overtemp.2

Fault signal: Motor overheated (input overtemperature 2

Roomtemp.max

Fault signal: Machine room temperature too high

Roomtemp.min

Fault signal: Machine room temperature too low

Содержание MLC 8000





































































































































































































Результаты поиска

Содержание MLC 8000

Отзывы:

Похожие инструкции для MLC 8000

Бренды по названию

Популярные бренды

Intec MLC 8000, Руководство по эксплуатации

Результаты поиска

Содержание MLC 8000

Отзывы:

Похожие инструкции для MLC 8000

Бренды по названию

Популярные бренды