Intec MLC 8000 Скачать руководство пользователя страница 37

Страница: 37 / 196

INTEC GmbH

22/12/2016

Lift controller MLC 8000

Operating manual V2.0

37/196

1. Menu level

2. Menu level

3. Menu level

4. Menu level

Description

no).

If set to "yes" emergency trips have higher priority than fire alarm

control (see below)

Run to fire

Indicates whether the floors can be reached in which a fire alarm is

active (yes / no)

Parking trip

Parameters for park ride

Park mode

Fixed: The lift goes to a fixed Park Floor

Zones: The lift is parked in the pre-defined zones (mainly for lift

groups)

Park floor

Park floor if park mode is "Fixed"

(Note: Up to version 1.32y this parameters is displayed in the menu

"General parameter")

Parktime[s]

If the lift is not used for this time the lift will go to the specified parking

level.

(Note: Up to version 1.32y this parameters is displayed in the menu

"Timer parameter")

Zone 1 Start

Bottom floor of the parking zone 1

Zone 1 Stop

Top floor of the parking zone 1

Note: If the top floor value is less than the bottom floor value, then the

parking zone is disabled

Zone 2 Start

See above

Zone 2 Stop

See above

....

Zone 8 Start

See above

Zone 8 Stop

See abov

Mand.zones

Specifies how many parking zones (starting with zone 1) must be

filled.

Example: In a group lift 1 is parked within zone 1 and lift 2 is parked in

zone 2. If lift 1 is called to another floor and the value of "Mandatory

zones" is> 0, then lift 2 goes to zone 1 and parks there. If the value

"Mandatory Zone = 0 he would remain in Zone 2.

Visitor calls

Parameters for visitors calls and visitor control

CC enabl.[s]

Time period car calls are enabled after the lift was sent to a floor by a

visitor call (type 1 and type 2)

LC enabl.[s]

Time period landing calls are enabled after a visitor call (type 1 and

type 3) was set.

Содержание MLC 8000





































































































































































































Результаты поиска

Содержание MLC 8000

Отзывы:

Бренды по названию

Популярные бренды

Intec MLC 8000, Руководство по эксплуатации

Результаты поиска

Содержание MLC 8000

Отзывы:

Бренды по названию

Популярные бренды