Intec MLC 8000 Скачать руководство пользователя страница 44

Страница: 44 / 196

INTEC GmbH

22/12/2016

Lift controller MLC 8000

Operating manual V2.0

44/196

1. Menu level

2. Menu level

3. Menu level

4. Menu level

Description

top shelter space was opened or inspection is switched on). In

standstill the bearer is switched off.

End off.: The bearer is only switched on if the lift arrives the top floor

Bearer

↓

Bearer type for safety shelter in shaft bottom:

No: No bearer necessary / available

manual: hand operated bearer

always: The bearer is always switched on in normal operation and

only switched off when the bottom shelter space is opened (e.g. by

opening shaft door in top floor) or the inspection control in pit is

switched on.

moving: The bearer is switched on while the lift is moving (but not if
top shelter space was opened or inspection in pit is switched on). In

standstill the bearer is switched off.

End off.: The bearer is only switched on if the lift arrives the bottom

floor.

Waitt.

↑

[s]

Max. Waiting time for feedback contacts of the top bearer after

switching an automatic bearer. If the bearer contacts did not switch

after this time, an error message follows.

Waitt.

↓

[s]

See above (for bearer in bottom)

Debounc. [ms]

Debouncing time for bearer contacts

Insp.

↑

[mm]

Extended slowing and stopping distance at inspection trip (with bearer

in upwards direction)

Insp.

↓

[mm]

Extended slowing and stopping distance at inspection trip (with bearer

in downwards direction)

Apron

no: No folding car apron available

manual: Manually operated car apron; which means, Apron needs to

be folded in manually in order to return to normal operation

Auto: utomatically operated car apron; which means, when folding

apron is extended, then automatically the lift moves when returning to

normal operation somewhere below the lowest floor to automatically

retract folding apron (apron is then held electric)

mechan.: Mechanically operated car apron; which is, Folding apron

pushes together when reaching the bottom floor , and ramps up when

leaving the lowest floor out again

Slow

↑

[mm]

Extended slow down distance for top floor, if lift is equipped with

folding apron.

Slow

↓

[mm]

See above; setting for bottom floor

Содержание MLC 8000





































































































































































































Результаты поиска

Содержание MLC 8000

Отзывы:

Похожие инструкции для MLC 8000

Бренды по названию

Популярные бренды

Intec MLC 8000, Руководство по эксплуатации

Результаты поиска

Содержание MLC 8000

Отзывы:

Похожие инструкции для MLC 8000

Бренды по названию

Популярные бренды