Intec MLC 8000 Скачать руководство пользователя страница 147

Страница: 147 / 196

INTEC GmbH

22/12/2016

Lift controller MLC 8000

Operating manual V2.0

147/196

Main function

Sub function/

Direction/

Floor

Doors

Description

-Bear.bot.Warn

in.

Car apron

Output for electrical locking of folding car apron.

Governor

Dir.

Output to activate a descent stopping system (e.g. coil on

overspeed governor, emergency stopping valve, A3 device, ….)

Uncontr.Mov

Output uncontrolled movement (UCM) detected.

Used to switch off safety circuit.

Hold.bolt

- Bolt out
- Bolt in

Output to pull in / pull out holding bolts.

- Bolt is out
- Bolt is in

Signal no.

Output for signaling "Holding bolt x is pulled out"

OP device

- Out
- In

Output to pull in / pull out the load derrick of a hospital operation

lift mit automatic loading / unloading.

- Right
- Left

Output to move the rotary table of a hospital operation lift mit

automatic loading / unloading.

Ramp

Output to switch the load interlock of a hospital operation lift mit

automatic loading / unloading.

Conn.IO

- "--"
- on delay
- off delay
- on+off
- Pulse
- Bistable

Signal no.

Delay[s]

See description of input function.

Additionally it may be defined for each single output

- on delay
- off delay

- on and off delay

- Pulse

The delay or pulse wide may be programmed with "Delay[s]".

By using the "Bistable" function the state of the output is toggled

always if the connected input is switched on.

Содержание MLC 8000





































































































































































































Результаты поиска

Содержание MLC 8000

Отзывы:

Похожие инструкции для MLC 8000

Бренды по названию

Популярные бренды

Intec MLC 8000, Руководство по эксплуатации

Результаты поиска

Содержание MLC 8000

Отзывы:

Похожие инструкции для MLC 8000

Бренды по названию

Популярные бренды