Intec MLC 8000 Скачать руководство пользователя страница 142

Страница: 142 / 196

INTEC GmbH

22/12/2016

Lift controller MLC 8000

Operating manual V2.0

142/196

Main function

Sub function/

Direction/

Floor

Doors

Description

Vis.request

Callfloor

Doors

Acknowledgement output for visitor request..

For more detailled description refer to "Special param. - Visitor

floors" in chapter "menu structure"

Hazard.call

Floor

Doors

Hazard call acknowledgement(see input functions)

Level displ.

Type:
- 1 of n
- Binary
- Graycode
- 7-Segm.
- 9-Seg.K

Signal no.

Offset

Outputs for controlling a conventional car level indicator (1-of-n-

coded, binary coded or Gray code). With 1-of-n setting the output is

set according to the setting "Signal no" in each floor.

For binary or gray code the signal number corresponds to the

relevant binary digit within the binary or Gray code.

Via the parameter "Offset" it can be selected, which binary or Gray

code value is output in which floor. When set to '1' the binary or

Gray code value 1 is set in the 1st floor, in floor 2 the value 2, etc.

When set to '0' the binary or Gray code value 0 is set in the 1st floor

(that means all outputs off), etc.

The assignment of the "Signal no." for a 7- or 9-segment display is

shown in the picture. For this type of displays it can be adjusted via

the "offset" if the units digit (= 1) or ten's digit (= 2) is to be

controlled.

Hall lantern

Dir.

Floor

Doors

The hall lantern output is used for signaling that the lift reaches a

floor. The signal is activated if the lift slows down for arrival.

Always the direction of the next handled call is displayed. The

signal is deactivated if the doors are closed again.

If no further call exists the hall lanterns for both directions are

displayed.

The settings "Dir.", "Floor" and "Doors" can be omitted optional;

then the output is valid for all directions / Floors / Doors.

Dir.arrow

Dir.

If the lift is moving the direction arrow for the travel direction is set,

while in standstill the direction to the next call is displayed.

While moving the arrows light up continuously; in standstill state

the arrows are flashing every second.

Mov.arrow

Dir.

Moving arrows always show the actual travel direction.

Gong

Dir.

Floor

Doors

Output to control a gong.

More settings see „Special param.“ - „Gong“

Speech

Direction up

Signal for speech unit for next travel direction upwards (set by

Содержание MLC 8000





































































































































































































Результаты поиска

Содержание MLC 8000

Отзывы:

Похожие инструкции для MLC 8000

Бренды по названию

Популярные бренды

Intec MLC 8000, Руководство по эксплуатации

Результаты поиска

Содержание MLC 8000

Отзывы:

Похожие инструкции для MLC 8000

Бренды по названию

Популярные бренды