Intec MLC 8000 Скачать руководство пользователя страница 40

Страница: 40 / 196

INTEC GmbH

22/12/2016

Lift controller MLC 8000

Operating manual V2.0

40/196

1. Menu level

2. Menu level

3. Menu level

4. Menu level

Description

Forc.door cl.

yes: Light screen is ignored when the door is closed; Door closes with

reduced force and speed; additionally, an audible signal sounds (if

present)

no: „Normal“ door closing

Door op.push

Setting if door open push is still active or disabled in fire evacuation

mode

Door state

opened: door remains open after reaching the relevant floor

reclose: Upon reaching the set floor the door opens and then closes

again

Dynamic mode

yes: If the lift has already moved to a "safe" level in case of fire, but

the fire alarm is activated than in this floor, then the lift drives to

another "safe" level.

no: after moving to a "safe" level in case of fire the lift will stay in this

floor, even if the fire alarm triggers in this floor.

Fire det.act.

no: The fire alarm of the individual floors are ignored unless the input

"fire" is enabled.

yes: the fire alarm of the individual floors are evaluated regardless of

the state of the input "fire".

Auto return

yes: After disabling the input "fire" (and, if parameter "Fire det .act " is

set to yes, all fire detectors on each floor; see above) the lift returns

back to normal operation.

no: The lift does not return to normal operation even after deactivation

of all fire signals.A Reset is necessary.

Run thr.fire

yes: The lift goes when needed, through the floor, where the fire alarm

is activated, to reach the nearest "safe" level.

no: The lift never goes through a floor where the fire alarm has been

activated.

Last trip

yes: Even if it is not possible, according to the settings “Fire evac.

floors” (see below), to approach one of the safe floors, (f.ex. because

all fire alarms had been triggered) the lift approaches the last fire floor,

according to this setting.

Last floor

Lift goes to this floor, if ther is no other safe floor avbailable (see

above).

Fire evac.floors

Setting of safe floorsin case of fire

F.Evac.fl.

In case of fire the lift will go to this floor if possible

F.Evac.fl.

If it is not possible to go to the 1st fire evacuation floor in case of fire

(see above), the lift will go to this 2nd fire evacuation floor.

…

Содержание MLC 8000





































































































































































































Результаты поиска

Содержание MLC 8000

Отзывы:

Похожие инструкции для MLC 8000

Бренды по названию

Популярные бренды

Intec MLC 8000, Руководство по эксплуатации

Результаты поиска

Содержание MLC 8000

Отзывы:

Похожие инструкции для MLC 8000

Бренды по названию

Популярные бренды