Intec MLC 8000 Скачать руководство пользователя страница 27

Страница: 27 / 196

INTEC GmbH

22/12/2016

Lift controller MLC 8000

Operating manual V2.0

27/196

1. Menu level

2. Menu level

3. Menu level

4. Menu level

Description

Fire evac. run

Released doors in case of fire detection

1.Floor

Released doors in 1st floor

2.Floor

…

Firemen run

Released doors for fireman trip

1.Floor

Released doors in 1st floor

2.Floor

…

Hazard transport

Released doors for hazard transportation mode

1.Floor

Released doors in 1st floor

2.Floor

…

Door park mode

If parking with open doors is enabled (see Door parameters), then here

it can be set individually for each floor, which doors should remain

open when the lift is on the equivalent floor.

1.Floor

Opened doors if lift is on 1st floor

2.Floor

Opened doors if lift is on 2nd floor

…

Door parameter

Parameters for up to 3 car doors

Gener.door para.

Cl.push

Operation of the door-close button

No delay: the door-close button is immediately active at the beginning

of the door opening, ie, the opening of the door can be interrupted by

pressing the door-close button and the door closes immediately

delayed.: button is not active until the door was fully open

Op.push D1

Operation of the door-open button for car door 1

all: open all the doors of the relevant floor.

last: The last opened doors will open again

enabled: All released doors according to the operation mode will be

opened (see parameter "Door releases" above)

Op.push D2

Operation of the door-open button for car door 2 (see above)

Op.push D3

Operation of the door-open button for car door 3 (see above)

Содержание MLC 8000





































































































































































































Результаты поиска

Содержание MLC 8000

Отзывы:

Похожие инструкции для MLC 8000

Бренды по названию

Популярные бренды

Intec MLC 8000, Руководство по эксплуатации

Результаты поиска

Содержание MLC 8000

Отзывы:

Похожие инструкции для MLC 8000

Бренды по названию

Популярные бренды