manualshive.com logo in svg

Intec MLC 8000, Руководство по эксплуатации

Поделиться
Скачать
Intec MLC 8000 Скачать руководство пользователя страница 9

INTEC GmbH  

 

 

 

 

    22/12/2016 

Lift controller MLC 8000 

 

Operating manual V2.0

 

 

 

9/196 

6.1.7 Testing the monitoring inputs for motor brake (roped lifts) or valves (hydraulic lifts)
 .................................................................................................................................... 115

 

6.1.8 Testing the contactor monitoring (Contactor drop off control) .............................. 116

 

6.1.9 Uncontrolled movement ...................................................................................... 116

 

6.2. Conventional Test .................................................................................................... 117

 

6.2.1 Testing the safety circuit for moving with open doors .......................................... 117

 

6.2.2 Testing the trip time monitoring ........................................................................... 117

 

6.2.3 Testing of parking trip to lowest floor by hydraulic lifts ......................................... 117

 

6.2.4 Testing of emergency light .................................................................................. 117

 

6.2.5 Testing the final limit switches ............................................................................. 117

 

6.2.6 Testing the traction (driving ability) ...................................................................... 118

 

6.2.7 Testing the speed monitoring .............................................................................. 118

 

7. Parameters of lift controller ................................................................................. 119

 

7.1 Saving parameters .................................................................................................... 119

 

7.2 Parameter backup ..................................................................................................... 119

 

7.3 Changing parameters ................................................................................................ 119

 

7.4 Changing of parameter “Floor name” ........................................................................ 120

 

7.5 Transferring parameters when replacing defective modules ...................................... 120

 

7.6 Parameters for freely programmable inputs and outputs ........................................... 121

 

7.7 Functions for free programmable inputs and outputs ................................................. 123

 

7.7.1. Input functions .................................................................................................... 123

 

7.7.2. Output functions ................................................................................................. 135

 

8. Setting the node ID ............................................................................................. 148

 

9. Group control ...................................................................................................... 148

 

9.1 Principle of Group control .......................................................................................... 148

 

9.2 Parameter synchronization within a lift group ............................................................ 150

 

10. State display ..................................................................................................... 151

 

10.1 State display 1 (General overview) .......................................................................... 151

 

10.2 State display 2 (Door state) ..................................................................................... 152

 

10.3 State display 3 (Timer values) ................................................................................. 153

 

10.4 State display 4 (Position and Speed) ....................................................................... 153

 

10.5 State display 5 (Emergency evacuation) ................................................................. 154

 

Appendix 1. Technical specifications ...................................................................... 155

 

Appendix 1.1 Module MCU ............................................................................................. 155

 

Appendix 1.2 Module HSE .............................................................................................. 159

 

Appendix 1.3 Module FVE 1.1 / FVE 2.1 ......................................................................... 164

 

Appendix 1.4 Module FVE 1.2 ......................................................................................... 170

 

Appendix 1.5 Module UEA .............................................................................................. 175

 

Appendix 1.6 Module PMA .............................................................................................. 178

 

Appendix 1.7 Module LCI16 ............................................................................................ 180

 

Appendix 1.8 Module TVE ............................................................................................... 183

 

Appendix 1.9 Module CBK .............................................................................................. 185

 

Appendix 1.10 Module SRU ............................................................................................ 187

 

Appendix 1.11 Module LCD-047 ..................................................................................... 188

 

Appendix 1.12 Module LCD-057 ..................................................................................... 191

 

Appendix 1.13 Handheld terminal ................................................................................... 196

 

 
 
 
 

Содержание MLC 8000





































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды