Intec MLC 8000 Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 196

background image

INTEC GmbH

22/12/2016

Lift controller MLC 8000

Operating manual V2.0

121/196

After switching on the power again, the HSE tests if there is a valid parameter set in the
EEPROM. If not, then following message appears " No actual parameter set! Load
default:ENT, Skip ESC ".

This message can have 3 different reasons:
- The EEPROM is actually empty or defective
- The two EEPROMs are reversed when changing
- There is a new HSE used with a different (newer) software version

If pressing ENTER, all parameters are checked for validity. All parameters that are within
their valid range are retained, all other parameters (for example, all in a new software version
newly added parameters) are set to a default value.

If, after the next reboot of the HSE (on / off voltage or reset button), this message appears
again, then the EEPROM is probably faulty.

Important note: When changing the HSE or replacing defective relays only relays

with 2 changeover contacts must be used!

7.6 Parameters for freely programmable inputs and outputs

Almost all inputs and outputs of the lift controller MLC 8000 are freely programmable and
have no fixed function.

The function of the inputs and outputs can be set by parameters via the keyboard of the HSE
or the hand-held terminal. It does not matter in most cases (exceptions: see description of
the relevant function) whether the input or output function is set for the HSE, the FVE or for
an ESE or TSE board.

There are only a few functions that can only be set to specific modules (e.g. drive
speed signals can only be programmed for ASE and HSE). Even it is possible to
programm such functions like speed signals to a FVE - they will not work.

A parameter for an input or output consists of 6 sub parameters:
- Main function

Fct

- Sub function

Sub

- Lift

Lift

- Floor

Floor

- Door

Door

- Switching Logic

Logic

Depending on the selected main function only the necessary sub parameters will be
displayed (for example if "Load" is selected as main function, the sub parameter "Door" is not
necessary and will not be displayed).

The sub parameter "Lift" is only displayed, if the input or output is programmed for an ESE
parameter.

Sometimes the name of any sub parameter is changed depending on the selected main
function (for example if "Land.call" is selected as main function, the name of the sub function

«
...
119
120
121
122
123
...
»

Содержание MLC 8000





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MLC 8000

Бренд: YOKOGAWA Страницы: 2

ALICAT SCIENTIFIC PC

Бренд: Halma Страницы: 2

ALICAT SCIENTIFIC PCD

Бренд: Halma Страницы: 46

coviva Smartbox TKP100A

Бренд: hager Страницы: 4

Бренд: Vag Страницы: 12

Бренд: Uniden Страницы: 28

Бренд: UniFocus Страницы: 23

Бренд: UniFocus Страницы: 6

Бренд: Vaillant Страницы: 32

Бренд: Vaillant Страницы: 27

Бренд: Vaillant Страницы: 40

Бренд: Vaillant Страницы: 36

Бренд: Vaillant Страницы: 28

Бренд: Vaillant Страницы: 92

Бренд: Nice Страницы: 120

Бренд: Click2Enter Страницы: 34

Бренд: Zencontrol Страницы: 2

Бренд: Gasboy Страницы: 119

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды