Intec MLC 8000 Скачать руководство пользователя страница 62

Страница: 62 / 196

INTEC GmbH

22/12/2016

Lift controller MLC 8000

Operating manual V2.0

62/196

1. Menu level

2. Menu level

3. Menu level

4. Menu level

Description

Errors

Error stack

Display all entries in the error stack (last 100 errors with time stamp)

Note: By pressing ENTER the error on which the cursor is currently
located, will display detailed information (see section "Error stack")

Error count

Display all entries of the error counter (frequency of each error)

Clear stack

Clear the entire error stack

Clear count

Clear the entire error counter

Hardware test

Hardware test of each control module.

Capital letters at the inputs / outputs indicate that the input / output is

set, by lowercase letters ,the input / output is not set.

The letters represent a short code for the function of the input / output.

By positioning the cursor on an output, and pressing the '0' key, the
state of the output for test can be changed for test purposes (switch

on / off the output).

Attention: Even while the lift is running this function is possible!

Therefore, think about the possible consequences before carrying out!

For the first 8 outputs of a circuit board, the outputs can be directly

set / reset by pressing the corresponding number key.

By positioning the cursor on an input or output and pressing ENTER

detailed informations about the input / outpunt function are displayed

and may also be changed here.

HSE In-/Outputs

Indication of the state of the inputs and outputs of the HSE; setting

outputs of HSE

Example:

HW:1.01 SW:1.13
Eee--rudSSSs-nVZ
SGM: 1
Sdlube--

1st line: Display of the hardware and software version

2nd line: state of the inputs of the HSE

3rd line: state of the door zone switch SGM

4th line: state of the outputs of the HSE

Bus node test

Here it is displayed whether the communication link (CAN bus, RS485

...) to the main control modules (FVE, ASE, PSE) works well or not.

Example:

Bus nodes:

Here are all control main modules displayed, which, depending on the

parameter settings, must be present.

If the communication to a module functions, then the software version

number after the module is displayed, otherwise '-' appears .

Содержание MLC 8000





































































































































































































Результаты поиска

Содержание MLC 8000

Отзывы:

Бренды по названию

Популярные бренды

Intec MLC 8000, Руководство по эксплуатации

Результаты поиска

Содержание MLC 8000

Отзывы:

Бренды по названию

Популярные бренды