IHI 55N3 Скачать руководство пользователя страница 95

Страница: 95 / 115

3 – 25

ᵑ

MAINTENAN

1000HOURS

10.Fill the hydraulic oil tank with oil.

See Recommended Lubricant Table.

11.Loosen the air purge valve

on the pump

housing. When oil flow of air bubbles, tighten
the purge valve

12.Start and operate the engine at idling speed for

five minutes.

13.Operate the control levers to allow the hydraulic

oil to circulate through all hydraulic circuits.

14.Lower the bucket to the ground with the arm and

bucket cylinder fully retracted and stop the engine.

15.Maintain the oil level between

FULL

and

ADD

marks on the level gauge

16.Pressurize the hydraulic oil tank.

Raise the boom with the arm, boom and bucket
cylinder fully extended.
Remove the fill plug

and then install fill plug

again.

17.Lower the bucket on the ground and stop the

engine.

Hydraulic Oil Change Intervals for Breaker
Works.

Hydraulic oil should be changed in every 500
service hours.

CAUTION

Bucket position at the time of

checking the hydraulic oil level.

Bucket position at the time of

sealing off hydraulic tank.

Содержание 55N3




















































































































Результаты поиска

Содержание 55N3

Отзывы:

IHI 55N3, Руководство по эксплуатации, Страница: 95 / 115

Результаты поиска

Содержание 55N3

Отзывы: