IHI 55N3 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 115

IHI 55N3 Скачать руководство пользователя страница 33

1 – 27

ᵏ

SAFETY

1-10 PARKING THE MACHINE

BANKS AND SLOPES

NEVER

leave the machine on or near any

bank which may case, or on the edge of an
excavation which might give way. Back the
machine away from such areas which it is to
be left idle or unattended for more than a brief
period. Whenever possible, park on level
ground.

DO NOT PARK THE MACHINE ON A
GRADE.

If you have to park the machine on a grade,

ALWAYS

lower the bucket and the blade onto

the ground and block the machine.

OBSERVE PRECAUTIONS WHEN
PARKING THE MACHINE ON THE ROAD.

If you have to park the machine on the road,
use appropriate flags, barriers, flares, and
warning signals.

OPERATOR LEAVING MACHINE

ALWAYS

lower attachments to rest on

ground and stop engine before leaving the
machine unattended.
Engage all locks, turn off the start switch, and
remove the start key. Lock the windows and
doors.

«
...
31
32
33
34
35
...
»

Содержание 55N3




















































































































Отзывы:

Нет отзывов