IHI 55N3 Скачать руководство пользователя страница 88

Страница: 88 / 115

3 – 18

ᵑ

MAINTENAN

250HOURS

Change the Secondary Element

* Always replace the secondary filter element.

NEVER

attempt to reuse it by cleaning.

* The secondary filter element should be

replaced at the time the primary element is
serviced for five time.

Replacement: When replaced the primary

element with the secondary element.

1. Remove the service cover

and the primary

element

from the air cleaner housing

2. Remove the secondary element

from the air

cleaner housing

. Cover the engine intake

opening.

3. Clean the inside of the air cleaner housing

and service cover

Remove the covering from

the intake opening.

NOTE:

Clean the seal tube in the cleaner housing.

Dust on the seal tube causes dust leak.

4. Install the new secondary element

5. Install the primary element

secure the service

cover

6. Reset the dust indicator

by pushing in the reset

button.

CAUTION

Indicator

Reset button

Clean

Seal Tube

Содержание 55N3




















































































































Результаты поиска

Содержание 55N3

Отзывы:

IHI 55N3, Руководство по эксплуатации, Страница: 88 / 115

Результаты поиска

Содержание 55N3

Отзывы: