IHI 55N3 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 115

IHI 55N3 Скачать руководство пользователя страница 11

1 – 5

ᵏ

SAFETY

MAINTAIN GOOD VENTILATION.

Take a countermeasure to vent the exhaust
gas to the outside to start and operate the
engine, in a pit, tunnel, or trench. In such a
place, the air trends to stagnate. It is very
dangerous to inhale the exhaust gas.
Remember, exhaust gas can kill you.

DO NOT MODIFY THE ROPS/TOPS.

Do not modify the

ROPS/TOPS

unless

instructed to do so in installation instructions.
Modifications such as welding, drilling or
cutting can weaken the structure and reduce
the protection it provides.
A damaged

ROPS/TOPS

can not be repaired

– it must be replaced.

1-2 MOUNTING AND DISMOUNTING

CAREFULLY MOUNT AND DISMOUNT
THE MACHINE.

ALWAYS

use steps and handholds to mount

and dismount the machine.
Hold the handholds with both hands and face
the machine keeping a contact with at least
three points of the steps and handrails.

NEVER

hold control levers at mounting and

dismounting.

NEVER

not try to mount or dismount the

moving machine.

NEVER

jump off the machine.

Do not try to climb on or off the machine with
implements or supplies in your hand.

«
...
9
10
11
12
13
...
»

Содержание 55N3




















































































































Отзывы:

Нет отзывов