IHI 55N3 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 115

IHI 55N3 Скачать руководство пользователя страница 66

2 – 24

ᵐ

O

PE

R

ATI

O

N

2-12 LIFTING THE MACHINE

Improper lifting or tie downs can allow load to shift and cause injury or damage.
* Use proper rated cables and slings for lifting. Lifting cables should have sufficient

length to prevent contact with machine.

* Position crane for level machine lift.
*

NEVER

lift the machine loaded with any personnel.

* Use guide or tag lines to prevent the machine from swinging or turning.
* Be sure to use are wire ropes with breaking force of greater than 10.6 tons.

Lifting Procedures

1. Start the engine and swing the machine

to position the blade to rear.

2. Position the machine on the level ground,

with the boom, arm and bucket cylinders
fully extended.

3. Position the boom at the center of the

machine with the boom swing pedal.

4. Stop the engine.
5. Install the cable to the two lifting eyes on

the blade with shackles.
Install the cable to the lifting eye on the
boom of the center with shackle.

6. Install the cables to the crane hook.
7. Confirm that no obstacles nor personal

are around the machine and have the
operator leave the machine.

8. Once the machine is lifted off the ground,

check that the machine is well balanced.

Machine mass (kg)

WARNING

Shoe type

Canopy

Cabin

Rubber shoe

5200

5330

Steel shoe

5250

5380

CAUTION

Selection of the lifting cables:
Be sure to use are wire ropes with
breaking force of greater than 10.6 tons.

«
...
64
65
66
67
68
...
»

Содержание 55N3




















































































































Отзывы:

Нет отзывов